###DEBCONF###
# the configuration of this file will be done by debconf as long as the
# first line of the file says '###DEBCONF###'
#
# you should use dpkg-reconfigure libnss-ldap to configure this file.
#
# @(#)$Id: ldap.conf,v 2.30 2001/09/22 10:57:56 lukeh Exp $
#
# This is the configuration file for the LDAP nameservice
# switch library and the LDAP PAM module.
#
# PADL Software
# http://www.padl.com
#

# Your LDAP server. Must be resolvable without using LDAP.
host 127.0.0.1

# The distinguished name of the search base.
base dc=myhome,dc=lan

# Another way to specify your LDAP server is to provide an
# uri with the server name. This allows to use
# Unix Domain Sockets to connect to a local LDAP Server.
#uri ldap://127.0.0.1/
#uri ldaps://127.0.0.1/   
#uri ldapi://%2fvar%2frun%2fldapi_sock/
# Note: %2f encodes the '/' used as directory separator

# The LDAP version to use (defaults to 3
# if supported by client library)
ldap_version 3

# The distinguished name to bind to the server with.
# Optional: default is to bind anonymously.
#binddn cn=proxyuser,dc=padl,dc=com

# The credentials to bind with. 
# Optional: default is no credential.
#bindpw secret

# The distinguished name to bind to the server with
# if the effective user ID is root. Password is
# stored in /etc/ldap.secret (mode 600)
#rootbinddn cn=manager,dc=padl,dc=com

# The port.
# Optional: default is 389.
#port 389

# The search scope.
#scope sub
#scope one
#scope base

# Search timelimit
#timelimit 30

# Bind timelimit
#bind_timelimit 30

# Idle timelimit; client will close connections
# (nss_ldap only) if the server has not been contacted
# for the number of seconds specified below.
#idle_timelimit 3600

# RFC2307bis naming contexts
# Syntax:
# nss_base_XXX		base?scope?filter
# where scope is {base,one,sub}
# and filter is a filter to be &'d with the
# default filter.
# You can omit the suffix eg:
# nss_base_passwd	ou=People,
# to append the default base DN but this
# may incur a small performance impact.
#nss_base_passwd	ou=People,dc=padl,dc=com?one
#nss_base_shadow	ou=People,dc=padl,dc=com?one
#nss_base_group		ou=Group,dc=padl,dc=com?one
#nss_base_hosts		ou=Hosts,dc=padl,dc=com?one
#nss_base_services	ou=Services,dc=padl,dc=com?one
#nss_base_networks	ou=Networks,dc=padl,dc=com?one
#nss_base_protocols	ou=Protocols,dc=padl,dc=com?one
#nss_base_rpc		ou=Rpc,dc=padl,dc=com?one
#nss_base_ethers	ou=Ethers,dc=padl,dc=com?one
#nss_base_netmasks	ou=Networks,dc=padl,dc=com?ne
#nss_base_bootparams	ou=Ethers,dc=padl,dc=com?one
#nss_base_aliases	ou=Aliases,dc=padl,dc=com?one
#nss_base_netgroup	ou=Netgroup,dc=padl,dc=com?one

# attribute/objectclass mapping
# Syntax:
#nss_map_attribute	rfc2307attribute	mapped_attribute
#nss_map_objectclass	rfc2307objectclass	mapped_objectclass

# configure --enable-nds is no longer supported.
# For NDS now do:
#nss_map_attribute uniqueMember member

# configure --enable-mssfu-schema is no longer supported.
# For MSSFU now do:
#nss_map_objectclass posixAccount User
#nss_map_attribute uid msSFUName
#nss_map_attribute uniqueMember posixMember
#nss_map_attribute userPassword msSFUPassword
#nss_map_attribute homeDirectory msSFUHomeDirectory
#nss_map_objectclass posixGroup Group
#nss_map_attribute cn msSFUName

# Alternatively, if you wish to equivalence W2K and POSIX
# groups, change the uniqueMember mapping line to:
#nss_map_attribute uniqueMember member

# configure --enable-authpassword is no longer supported
# For authPassword support, now do:
#nss_map_attribute userPassword authPassword

# For IBM AIX SecureWay support, do:
#nss_map_objectclass posixAccount aixAccount
#nss_base_passwd ou=aixaccount,?one
#nss_map_attribute uid userName
#nss_map_attribute gidNumber gid
#nss_map_attribute uidNumber uid
#nss_map_attribute userPassword passwordChar
#nss_map_objectclass posixGroup aixAccessGroup
#nss_base_group ou=aixgroup,?one
#nss_map_attribute cn groupName
#nss_map_attribute uniqueMember member
# Next line added by Sourceforge install
rootbinddn cn=admin,dc=myhome,dc=lan