[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Discuss-gnuradio] Re: A Humble Request....for allowing to copy Circ

From: Sanjay Singh
Subject: Re: [Discuss-gnuradio] Re: A Humble Request....for allowing to copy Circuit into PCB
Date: Wed, 12 Jan 2011 20:56:59 +0530

Hi All,

I have USRP1(4.5 Version) purchased from Matt Ettus around 2 years back.

Am interested to sell them at half price. I have two mother boards with four daughter boards. I had purchased it for experimenting MIMO based designs. Since am not at all using them, now am planning to sell them. Boards are barely used and are as brand new one.

Am from India. Please get back via mail with your contacts. 


On Mon, Jan 3, 2011 at 11:28 PM, Marten Christophe <address@hidden> wrote:
Hello ALL,
Does you have an answer to my request , is there something for charity 
there is possibility for like me to use USRP1.
Kind Regards,

On Sun, Dec 12, 2010 at 10:14 PM, Marten Christophe <address@hidden> wrote:
Hello Matt, and All,
Is there possible,  you can sell only USRP1 board with all components, only board no enclosure no power supply only board. with all component soldered to it , i will arrange specified ratting power supply here locally,
why i'm requesting it due to i'm a student and dont have that much money to buy full USRP1+shipping charges
if you can send only USRP board without enclosures and power supply it will reduce shipping cost
i have arrange so far $ 300  only  , so if it is possible , i will be thankful to all of you, USRP1 is very much needed for my practicals and study
you ought to run a program to sell your product to poor students at discounted rate as Ettus Research being a big organisation now , but USRP1 was developed as a open source  hardware with the help of community  and very use full for us.
Thanks and Kind regards,

On Thu, Nov 4, 2010 at 7:44 PM, Marten Christophe <address@hidden> wrote:
Hello Mr. Ettus,

Thanks a lot, at least  for you reply.
Now  I will have to search some other cheap SDR, or will have to wait another one year when i will get my scholarship
then buy your marvelous product the USRP1..

Thanks and Kind regards,

On Fri, Nov 5, 2010 at 1:08 AM, Matt Ettus <address@hidden> wrote:

No.  We do not have or sell blank PCBs.


On 11/04/2010 12:30 PM, Marten Christophe wrote:
Ohhhh, Mr. Ettus,

at least give me a blank PCB, coz by very hard work i have collected IC
, FPGA , and all other things, by requesting sample part, if i were moneyed
i must have buy USRP1,

if i will have a blank PCB at least i will sold all parts , and i wont
have to copy any others work, and design , and i will kept away my self
from theft, you know,
even i will PAY  the blank PCB material cost. and postal charges, from
US to india, but i buy USRP1 , that i need to shiped, and again high amount.

after all i'm student...from India.

Kind Regards,

On Fri, Nov 5, 2010 at 12:51 AM, Matt Ettus <address@hidden
<mailto:address@hidden>> wrote:


   On 11/04/2010 12:20 PM, Marten Christophe wrote:

       Hello Mr. Ettus ,

       If you are unable to provide that , know problem , but least
       reply my
       mail with negation so i wont wait and for you, and start trying to
       design PCB
       with the help of you .SCH file of USRP 1 and will collect money to
       fabricate it, but for only one PCB it take around $500 start
       cost. :(
       and more over before doing so, i want you permission b'coze it was
       designed by you so if it is my moral responsibility to seek your
       permission on first place.

       Kind Regards,
       Devendra Purohit

       On Thu, Nov 4, 2010 at 12:02 AM, Marten Christophe
       <address@hidden <mailto:address@hidden>
       <mailto:address@hidden <mailto:address@hidden>>>

           On Mon, Nov 1, 2010 at 11:04 PM, Marten Christophe
       <address@hidden <mailto:address@hidden>
       <mailto:address@hidden <mailto:address@hidden>>>

               Hello Mr. Ettus,

               Kindly provide me USRP motherboard Blank PCB board. i
       will pay
               for postage and material cost.
               I'm a poor student and USRP is needed for my research
       work and
               study, i have almost all components collected by sampling
               so i can assemble and sold all of them
               if i will have PCB .
               $1400+400+ UPS courier charges(oversease shipping) it is
               my ability to spend.
               I'm a private Student and keen to learn,but I'm poor too
       , hence
               don't have capability to buy USRP,
               so I'm also trying to make USRP my self. but dont' have
               resources to fabricate PCB.
               though i have collected all component some of those were
               i arranged samples,
               only thing left is PCB. can you kindly help me to give
       me blank
               PCB for USRP ( whether usrp1 or usrp2) mother and daughter
               board . I will pay the cost what ever it would be for
       postage and
               your material in advance.
               also i need you generous help also , at least guidance.
               I'm Doing MS in Communication system by distance learning
               program of a Govt university.
               Kind Regards,
               Manoj Kumar ( India )

Discuss-gnuradio mailing list

reply via email to

[Prev in Thread] Current Thread [Next in Thread]