discuss-gnuradio
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Discuss-gnuradio] Gnuradio-companion


From: Dennis Glatting
Subject: Re: [Discuss-gnuradio] Gnuradio-companion
Date: Wed, 18 Nov 2015 17:03:27 -0800

On Wed, 2015-11-18 at 19:54 -0500, Marcus D. Leech wrote:
> On 11/18/2015 07:16 PM, Sumit Saluja wrote:
> > Hi Marcus,
> >  
> > I am trying to install it on Our departmental cluster which is
> > RHEL6.7. Right now we can’t update to  RHEL7  or CENTOS7
> > 

Can you install CentOS/Debian/Ubuntu/etc in a virtual container?


> >  
> > Thanks
> > Sumit Saluja
> Not much we can do, I don't think.  The version of Boost on your
> system is not compatible with UHD.
> 
> You could install compatible boost from source, and try again.
> 
> 
> >  
> > From: address@hidden [mailt
> > o:address@hidden On Behalf
> > Of Marcus Müller
> > Sent: Wednesday, November 18, 2015 6:09 PM
> > To: address@hidden
> > Subject: Re: [Discuss-gnuradio] Gnuradio-companion
> >  
> > Dear Sumit. 
> > 
> > I just noticed this thread:
> > you're using RHEL 6, which only hast Boost 1.41; UHD cannot build
> > with anything below Boost 1.46.
> > 
> > Is there a particular reason for sticking with this very old
> > version, or can you upgrade to RHEL7 or CentOS7?
> > 
> > Best regards,
> > Marcus
> > 
> > On 18.11.2015 23:43, Sumit Saluja wrote:
> > Please see the logs with -v option
> > 
> > 
> > ./build-gnuradio -v
> > This script will install Gnu Radio from current GIT sources
> > You will require Internet access from the computer on which this
> > script runs. You will also require SUDO access. You will require
> > approximately 500MB of free disk space to perform the build.    
> >                                                                 
> > This script will, as a side-effect, remove any existing Gnu Radio
> > installation that was installed from your Linux distribution
> > packages.
> > It must do this to prevent problems due to interference between    
> >    
> > a linux-distribution-installed Gnu Radio/UHD and one installed from
> > GIT source.
> >                                                                    
> >             
> > The whole process may take up to two hours to complete, depending
> > on the       
> > capabilities of your system.                                       
> >             
> > 
> > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
> > !!!!!!!!!!!!!
> > NOTE: if you run into problems while running this script, you can
> > re-run it with
> > the --verbose option to produce lots of diagnostic output to help
> > debug problems.
> > This script has been written to anticipate some of the more common
> > problems one might
> > encounter building ANY large, complex software package. But it is
> > not pefect, and    
> > there are certainly some situations it could encounter that it
> > cannot deal with      
> > gracefully. Altering the system configuration from something
> > reasonably standard,    
> > removing parts of the filesystem, moving system libraries around
> > arbitrarily, etc,   
> > it likely cannot cope with. It is just a script. It isn't intuitive
> > or artificially  
> > intelligent. It tries to make life a little easier for you, but at
> > the end of the day
> > if it runs into trouble, a certain amount of knowledge on your part
> > about            
> > system configuration and idiosyncrasies will inevitably be
> > necessary.                
> > 
> > 
> > Proceed?yes
> > Starting all functions at: Wed Nov 18 17:38:05 EST 2015
> > SUDO privileges are required                           
> > Do you have SUDO privileges?yes                        
> > Continuing with script                                 
> > ./build-gnuradio: line 1410: [: 90                     
> > 90                                                     
> > 90                                                     
> > 90                                                     
> > 90                                                     
> > 90                                                     
> > 90                                                     
> > 90                                                     
> > 90                                                     
> > 90: integer expression expected                        
> > Installing prerequisites.                              
> > ====> THIS MAY TAKE QUITE SOME TIME <=====             
> > Loaded plugins: refresh-packagekit, security           
> > Setting up Remove Process                              
> > No Match for argument: gnuradio*                       
> > No Packages marked for removal                         
> > Loaded plugins: refresh-packagekit, security           
> > Setting up Remove Process                              
> > No Match for argument: libgruel-*                      
> > No Packages marked for removal                         
> > Loaded plugins: refresh-packagekit, security           
> > Setting up Remove Process                              
> > No Match for argument: libgruel*                       
> > No Packages marked for removal                         
> > Loaded plugins: refresh-packagekit, security           
> > Setting up Group Process                               
> > Warning: Group Engineering and Scientific does not exist.
> > Package flex-2.5.35-9.el6.x86_64 already installed and latest
> > version
> > Package gcc-4.4.7-16.el6.x86_64 already installed and latest
> > version 
> > Package redhat-rpm-config-9.0.3-44.sl6.noarch already installed and
> > latest version
> > Package rpm-build-4.8.0-47.el6.x86_64 already installed and latest
> > version        
> > Package 1:make-3.81-20.el6.x86_64 already installed and latest
> > version            
> > Package patch-2.6-6.el6.x86_64 already installed and latest version
> >                
> > Package 1:pkgconfig-0.23-9.1.el6.x86_64 already installed and
> > latest version      
> > Package gettext-0.17-18.el6.x86_64 already installed and latest
> > version           
> > Package automake-1.11.1-4.el6.noarch already installed and latest
> > version         
> > Package bison-2.4.1-5.el6.x86_64 already installed and latest
> > version             
> > Package flex-devel-2.5.35-9.el6.x86_64 already installed and latest
> > version       
> > Package libtool-2.2.6-15.5.el6.x86_64 already installed and latest
> > version        
> > Package autoconf-2.63-5.1.el6.noarch already installed and latest
> > version         
> > Package gcc-c++-4.4.7-16.el6.x86_64 already installed and latest
> > version          
> > Package binutils-2.20.51.0.2-5.43.el6.x86_64 already installed and
> > latest version 
> > Package patchutils-0.3.1-3.1.el6.x86_64 already installed and
> > latest version      
> > Package byacc-1.9.20070509-7.el6.x86_64 already installed and
> > latest version      
> > Package indent-2.2.10-7.el6.x86_64 already installed and latest
> > version           
> > Package systemtap-2.7-2.el6.x86_64 already installed and latest
> > version           
> > Package diffstat-1.51-2.el6.x86_64 already installed and latest
> > version           
> > Package elfutils-0.161-3.el6.x86_64 already installed and latest
> > version          
> > Package cvs-1.11.23-16.el6.x86_64 already installed and latest
> > version            
> > Package rcs-5.7-37.el6.x86_64 already installed and latest version 
> >                
> > Package subversion-1.6.11-15.el6_7.x86_64 already installed and
> > latest version    
> > Package gcc-gfortran-4.4.7-16.el6.x86_64 already installed and
> > latest version     
> > Package 1:doxygen-1.6.1-6.el6.x86_64 already installed and latest
> > version         
> > Package intltool-0.41.0-1.1.el6.noarch already installed and latest
> > version       
> > Package git-1.8.3.1-1.sdl6.x86_64 already installed and latest
> > version            
> > Package ctags-5.8-2.el6.x86_64 already installed and latest version
> >                
> > Package cscope-15.6-6.el6.x86_64 already installed and latest
> > version             
> > Package swig-1.3.40-6.el6.x86_64 already installed and latest
> > version             
> > Warning: Group development does not have any packages.             
> >                
> > No packages in any requested group available to install or update  
> >                
> > Loaded plugins: refresh-packagekit, security                       
> >                
> > Setting up Install Process                                         
> >                
> > Package fftw-devel-3.2.1-3.1.el6.x86_64 already installed and
> > latest version      
> > Package cppunit-devel-1.12.1-3.1.el6.x86_64 already installed and
> > latest version  
> > Package wxPython-devel-2.8.12.0-1.puias6.x86_64 already installed
> > and latest version
> > Package libusb-devel-0.1.12-23.el6.x86_64 already installed and
> > latest version      
> > Package boost-devel-1.41.0-27.el6.x86_64 already installed and
> > latest version       
> > Package alsa-lib-devel-1.0.22-3.el6.x86_64 already installed and
> > latest version     
> > Package 1:numpy-1.6.2-0.1.puias6.x86_64 already installed and
> > latest version        
> > Package gsl-devel-1.13-1.el6.x86_64 already installed and latest
> > version            
> > Package python-devel-2.6.6-64.el6.x86_64 already installed and
> > latest version       
> > No package pygsl available.                                        
> >                  
> > Package python-cheetah-2.4.1-1.el6.x86_64 already installed and
> > latest version      
> > Package python-mako-0.3.4-1.el6.noarch already installed and latest
> > version         
> > Package python-lxml-2.2.3-1.1.el6.x86_64 already installed and
> > latest version       
> > Package PyOpenGL-3.0.0-2.1.el6.noarch already installed and latest
> > version          
> > Package 1:qt-devel-4.6.2-28.el6_5.x86_64 already installed and
> > latest version       
> > Package 1:qt-4.6.2-28.el6_5.x86_64 already installed and latest
> > version             
> > Package 1:qt-4.6.2-28.el6_5.x86_64 already installed and latest
> > version             
> > Package 1:qt-devel-4.6.2-28.el6_5.x86_64 already installed and
> > latest version       
> > Package PyQt4-devel-4.6.2-9.el6.x86_64 already installed and latest
> > version         
> > Package qwt-devel-5.1.1-4.1.el6.x86_64 already installed and latest
> > version         
> > Package qwtplot3d-qt4-devel-0.2.7-9.el6.x86_64 already installed
> > and latest version 
> > Package libusb-0.1.12-23.el6.x86_64 already installed and latest
> > version            
> > Package libusb-devel-0.1.12-23.el6.x86_64 already installed and
> > latest version      
> > Package libusb1-1.0.9-0.6.rc1.el6.x86_64 already installed and
> > latest version       
> > Package libusb1-devel-1.0.9-0.6.rc1.el6.x86_64 already installed
> > and latest version 
> > Package cmake-2.8.12.2-4.el6.x86_64 already installed and latest
> > version            
> > Package git-1.8.3.1-1.sdl6.x86_64 already installed and latest
> > version              
> > Package wget-1.12-5.el6_6.1.x86_64 already installed and latest
> > version             
> > Package python-docutils-0.6-1.el6.noarch already installed and
> > latest version       
> > Package PyQwt-5.2.0-11.puias6.x86_64 already installed and latest
> > version           
> > Package PyQwt-devel-5.2.0-11.puias6.x86_64 already installed and
> > latest version     
> > Package qwt-devel-5.1.1-4.1.el6.x86_64 already installed and latest
> > version         
> > Package gtk2-engines-2.18.4-5.el6.x86_64 already installed and
> > latest version       
> > Package xmlrpc-c-client-1.16.24-1210.1840.el6.x86_64 already
> > installed and latest version
> > Package xmlrpc-c-c++-1.16.24-1210.1840.el6.x86_64 already installed
> > and latest version   
> > Package xmlrpc-c-devel-1.16.24-1210.1840.el6.x86_64 already
> > installed and latest version 
> > Package xmlrpc-c-apps-1.16.24-1210.1840.el6.x86_64 already
> > installed and latest version  
> > Package xmlrpc-c-1.16.24-1210.1840.el6.x86_64 already installed and
> > latest version       
> > Package xmlrpc-c-client++-1.16.24-1210.1840.el6.x86_64 already
> > installed and latest version
> > No package libzmq available.                                       
> >                         
> > No package libzmq-dev available.                                   
> >                         
> > Package tkinter-2.6.6-64.el6.x86_64 already installed and latest
> > version                   
> > Package orc-0.4.16-6.el6.x86_64 already installed and latest
> > version                       
> > Package python-requests-2.6.0-3.el6.noarch already installed and
> > latest version            
> > Nothing to do                                                      
> >                        
> > Checking for library libusb ...Found library libusb                
> >                         
> > Checking for library libboost ...Found library libboost            
> >                         
> > Checking for library libcppunit ...Found library libcppunit        
> >                         
> > Checking for library libfftw ...Found library libfftw              
> >                         
> > Checking for library libgsl ...Found library libgsl                
> >                         
> > Done                                                               
> >                         
> > This script will fetch Gnu Radio version 3.7/maint from the
> > repositories, along with compatible
> > extras.                                                            
> >                             
> > Is this OK?yes                                                     
> >                            
> > Fetching various packages (Gnu Radio, UHD, gr-osmosdr, gr-iqbal,
> > etc)                          
> > via the Internet                                                   
> >                            
> > =======> THIS MAY TAKE QUITE SOME TIME <=========                  
> >                             
> > Fetching Gnu Radio via GIT...Cloning into 'gnuradio'...            
> >                             
> > Submodule 'volk' (https://github.com/gnuradio/volk.git) registered
> > for path 'volk'             
> > Cloning into 'volk'...                                             
> >                            
> > remote: Counting objects: 5589, done.
> > remote: Total 5589 (delta 0), reused 0 (delta 0), pack-reused 5589
> > Receiving objects: 100% (5589/5589), 1.58 MiB | 266.00 KiB/s, done.
> > Resolving deltas: 100% (3997/3997), done.                          
> > Submodule path 'volk': checked out
> > 'f0b722392950bf7ede7b32f5ff60019bce7a8592'
> > M       volk                                                       
> >           
> > Branch maint set up to track remote branch maint from origin.      
> >           
> > Switched to a new branch 'maint'                                   
> >           
> > Done                                                               
> >           
> > Fetching UHD via GIT...Cloning into 'uhd'...                       
> >           
> > remote: Counting objects: 53257, done.
> > remote: Compressing objects: 100% (33/33), done.
> > remote: Total 53257 (delta 4), reused 0 (delta 0), pack-reused
> > 53224
> > Receiving objects: 100% (53257/53257), 96.50 MiB | 1.25 MiB/s,
> > done.
> > Resolving deltas: 100% (40626/40626), done.                        
> > Fetching rtl-sdr (rtl-sdr, gr-osmosdr, gr-iqbal, hackrf, bladeRF
> > and airspy) via GIT
> > Cloning into 'rtl-sdr'...                                          
> >                  
> > remote: Counting objects: 1617, done.
> > remote: Compressing objects: 100% (711/711), done.
> > remote: Total 1617 (delta 1182), reused 1213 (delta 898)
> > Receiving objects: 100% (1617/1617), 345.89 KiB | 529.00 KiB/s,
> > done.
> > Resolving deltas: 100% (1182/1182), done.                          
> >   
> > Cloning into 'gr-osmosdr'...                                       
> >   
> > remote: Counting objects: 3818, done.
> > remote: Compressing objects: 100% (2510/2510), done.
> > remote: Total 3818 (delta 2737), reused 1886 (delta 1270)
> > Receiving objects: 100% (3818/3818), 925.99 KiB | 876.00 KiB/s,
> > done.
> > Resolving deltas: 100% (2737/2737), done.                          
> >   
> > Cloning into 'gr-iqbal'...                                         
> >   
> > remote: Counting objects: 219, done.
> > remote: Compressing objects: 100% (175/175), done.
> > remote: Total 219 (delta 109), reused 98 (delta 40)
> > Receiving objects: 100% (219/219), 130.17 KiB | 0 bytes/s, done.
> > Resolving deltas: 100% (109/109), done.                         
> > Cloning into 'bladeRF'...                                       
> > remote: Counting objects: 16325, done.
> > remote: Total 16325 (delta 0), reused 0 (delta 0), pack-reused
> > 16325
> > Receiving objects: 100% (16325/16325), 6.81 MiB | 1.37 MiB/s, done.
> > Resolving deltas: 100% (9380/9380), done.                          
> > Submodule 'libosmo-dsp' (git://git.osmocom.org/libosmo-dsp)
> > registered for path 'libosmo-dsp'
> > Cloning into 'libosmo-dsp'...                                      
> >                          
> > remote: Counting objects: 172, done.
> > remote: Compressing objects: 100% (106/106), done.
> > remote: Total 172 (delta 89), reused 123 (delta 58)
> > Receiving objects: 100% (172/172), 60.12 KiB | 0 bytes/s, done.
> > Resolving deltas: 100% (89/89), done.                          
> > Submodule path 'libosmo-dsp': checked out
> > 'f9df8894c72cbd491bdd2f6d4cbea95c46810267'
> > Cloning into 'hackrf'...                                           
> >                  
> > remote: Counting objects: 9629, done.
> > remote: Total 9629 (delta 0), reused 0 (delta 0), pack-reused 9629
> > Receiving objects: 100% (9629/9629), 24.49 MiB | 21.42 MiB/s, done.
> > Resolving deltas: 100% (6741/6741), done.                          
> > Cloning into 'host'...                                             
> > remote: Counting objects: 626, done.
> > remote: Total 626 (delta 0), reused 0 (delta 0), pack-reused 626
> > Receiving objects: 100% (626/626), 587.24 KiB | 0 bytes/s, done.
> > Resolving deltas: 100% (452/452), done.                         
> > Done                                                            
> > Starting function uhd_build at: Wed Nov 18 17:41:12 EST 2015    
> > Building UHD...                                                 
> > =============> THIS WILL TAKE SOME TIME <=============          
> > 
> > -- The CXX compiler identification is GNU 4.4.7
> > -- The C compiler identification is GNU 4.4.7  
> > -- Check for working CXX compiler: /usr/bin/c++
> > -- Check for working CXX compiler: /usr/bin/c++ -- works
> > -- Detecting CXX compiler ABI info                      
> > -- Detecting CXX compiler ABI info - done               
> > -- Check for working C compiler: /usr/bin/cc
> > -- Check for working C compiler: /usr/bin/cc -- works
> > -- Detecting C compiler ABI info
> > -- Detecting C compiler ABI info - done
> > --
> > -- Configuring the python interpreter...
> > -- Found PythonInterp: /usr/lib/python2.7/bin/python (found version
> > "2.7.8")
> > -- Python interpreter: /usr/lib/python2.7/bin/python
> > -- Override with: -DPYTHON_EXECUTABLE=<path-to-python>
> > -- Using UHD Images Directory: OFF
> > -- Build type not specified: defaulting to release.
> > -- Performing Test HAVE_VISIBILITY_HIDDEN
> > -- Performing Test HAVE_VISIBILITY_HIDDEN - Success
> > -- Performing Test HAVE_VISIBILITY_INLINES_HIDDEN
> > -- Performing Test HAVE_VISIBILITY_INLINES_HIDDEN - Success
> > --
> > -- Configuring Boost C++ Libraries...
> > -- Could NOT find Boost
> > -- Boost include directories: /usr/include
> > -- Boost library directories: /usr/lib64
> > -- Boost libraries:
> > -- Looking for log2
> > -- Looking for log2 - found
> > --
> > -- Python checking for Python version 2.6 or greater
> > -- Python checking for Python version 2.6 or greater - found
> > --
> > -- Python checking for Mako templates 0.4 or greater
> > -- Python checking for Mako templates 0.4 or greater - found
> > --
> > -- Configuring LibUHD support...
> > --   Dependency Boost_FOUND = 0
> > --   Dependency HAVE_PYTHON_PLAT_MIN_VERSION = TRUE
> > --   Dependency HAVE_PYTHON_MODULE_MAKO = TRUE
> > CMake Error at cmake/Modules/UHDComponent.cmake:51 (MESSAGE):
> >   Dependencies for required component LibUHD not met.
> > Call Stack (most recent call first):
> >   CMakeLists.txt:279 (LIBUHD_REGISTER_COMPONENT)
> > 
> > 
> > -- Configuring incomplete, errors occurred!
> > See also
> > "/home/ssaluja/test/uhd/host/build/CMakeFiles/CMakeOutput.log".
> > make: *** No rule to make target `clean'.  Stop.
> > make: *** No targets specified and no makefile found.  Stop.
> > UHD build apparently failed
> > Exiting UHD build
> > 
> > ===================================================================
> > ====
> > If you have found this script useful and time-saving, consider a
> > donation to help me keep build-gnuradio, simple_ra, SIDsuite,
> > meteor_detector, simple_fm_rcv, and multimode maintained and up to
> > date.
> > A simple paypal transfer to address@hidden is all you need to
> > do.
> > ===================================================================
> > ===
> > Send success/fail info to sbrac.org?
> > 
> > From: address@hidden [
> > address@hidden on behalf
> > of Marcus D. Leech address@hidden
> > Sent: Wednesday, November 18, 2015 3:58 PM
> > To: address@hidden
> > Subject: Re: [Discuss-gnuradio] Gnuradio-companion
> > 
> > On 11/18/2015 03:45 PM, Sumit Saluja wrote:
> > If I am building gnuradio manually Iam getting following message 
> >  ######################################################
> > -- # Gnuradio disabled components
> > -- ######################################################
> > --   * gr-ctrlport
> > --   * gnuradio-companion
> > --   * gr-comedi
> > --   * gr-uhd
> > --   * gr-video-sdl
> > --   * gr-wxgui
> > --   * gr-zeromq
> > 
> > 
> > 
> > If I am building Gnuradio using build-gnuradio script then getting
> > following error
> > 
> > ====> THIS MAY TAKE QUITE SOME TIME <=====
> > Checking for library libusb ...Found library libusb
> > Checking for library libboost ...Found library libboost
> > Checking for library libcppunit ...Found library libcppunit
> > Checking for library libfftw ...Found library libfftw
> > Checking for library libgsl ...Found library libgsl
> > Done
> > This script will fetch Gnu Radio version 3.7/maint from the
> > repositories, along with compatible
> > extras.
> > Is this OK?yes
> > Fetching various packages (Gnu Radio, UHD, gr-osmosdr, gr-iqbal,
> > etc)
> > via the Internet
> > =======> THIS MAY TAKE QUITE SOME TIME <=========
> > Fetching Gnu Radio via GIT...Done
> > Fetching UHD via GIT...Fetching rtl-sdr (rtl-sdr, gr-osmosdr, gr
> > -iqbal, hackrf, bladeRF and airspy) via GIT
> > Done
> > Starting function uhd_build at: Wed Nov 18 15:44:13 EST 2015
> > Building UHD...
> > =============> THIS WILL TAKE SOME TIME <=============
> > 
> > UHD build apparently failed
> > Exiting UHD build
> > 
> > 
> > 
> > 
> > Thanks
> > Sumit Saluja
> > 
> > If you run build-gnuradio with -v, you'll get more logs, and likely
> > a note from Cmake that it couldn't find some depend that gnuradio
> > -companion relies on.
> > 
> > 
> > 
> >  
> > 
> > From: 18740449846 address@hidden
> > Sent: Monday, November 16, 2015 7:56 PM
> > To: Sumit Saluja
> > Subject: »Ø¸´: [Discuss-gnuradio] Gnuradio-companion
> > 
> > hi
> > you need give some detail
> > for example 
> > how do you build the gnuradio-companion and is you conmmand work
> > well show us the result 
> > this is useful to solve you problem
> > 
> > -----From Ekko
> > 
> > 
> > -------- ԭʼÓʼþ --------
> > Ö÷Ì⣺[Discuss-gnuradio] Gnuradio-companion
> > ·¢¼þÈË£ºSumit Saluja 
> > address@hidden
> > ³­ËÍ£º
> > 
> > 
> > Hi,
> > I am building gnuradio  on RHEL 6 and gnuradio-companion is not
> > enabling .  How I Should enable gnuradio-companion
> > And UHD is not compiling on RHEL6.
> >  
> >  
> > Thanks
> >  
> > Sumit Saluja
> > 
> > 
> > _______________________________________________
> > Discuss-gnuradio mailing list
> > address@hidden
> > https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
> >  
> > 
> > 
> > 
> > _______________________________________________
> > Discuss-gnuradio mailing list
> > address@hidden
> > https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
> >  
> > 
> > 
> > _______________________________________________
> > Discuss-gnuradio mailing list
> > address@hidden
> > https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
> _______________________________________________
> Discuss-gnuradio mailing list
> address@hidden
> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio



reply via email to

[Prev in Thread] Current Thread [Next in Thread]