Fw: [Ltib] Can't build after CVS update

[Matt Waddel]

Hi Bob,

Are you starting a new project?  If you are, use the 5329 selection in 
the cf-nommu bsp.  That BSP uses the 2.6.26-uc0 kernel.  The 
2.6.26 kernel is a much better starting point than the 2.6.22 kernel.

--Matt



----- Original Message ----
From: Stuart Hughes <address@hidden>
To: address@hidden
Cc: address@hidden
Sent: Thursday, April 16, 2009 2:54:42 AM
Subject: Re: [Ltib] Can't build after CVS update

Hi Bob,

It looks like you were running an scbuild (or similar) and the auto-generated 
spec file wasn't unlinked (maybe you Ctrl-C-ed) and is being picked up on 
subsequent runs.  Try doing this:

$ mv /home/rsg/ltib/rpm/SPECS/kernel-2.6.22-uc1.spec kernel.spec.bad
$ ./ltib

This is a bug and I'll put a fix in when I get a chance.

Regards, Stuart

Robert S. Grimes wrote:
> Hi,
> 
> Just did an update of CVS, and now I can't build my ltib.  When I
> try ./ltib -c, I get the first screen (caption is "LTIB: Freescale
> M532xEVB Coldfire/M68k (noMMU)") is displayed, but when I select
> "Configure the kernel" and hit Exit, I get the following errors:
> 
> 
> $ ./ltib -c
> + [ -n  ]
> + [ -f /home/rsg/ltib/config/.config ]
> + [ ! -f config/platform/m532xevb/.config -a -f
> config/platform/m532xevb/defconfig ]
> + [ -n  ]
> + cd config/platform/m532xevb
> + mconf main.lkc .config
> 
> 
> *** End of configuration.
> *** Check the top-level Makefile for additional configuration options.
> 
> + cp .config defconfig.dev
> 
> Processing platform: Freescale M532xEVB Coldfire/M68k (noMMU)
> ===============================================================
> using config/platform/m532xevb/.config
> 
> Processing: fake-provides
> ===========================
> 
> Processing: kernel-2.6.22-uc1
> ===============================
> Build path taken because: no prebuilt rpm, 
> rpmbuild --dbpath /home/rsg/ltib/rootfs//var/lib/rpm --target m68knommu
> --define '_unpackaged_files_terminate_build 0' --define '_target_cpu
> m68knommu' --define '__strip strip' --define
> '_topdir /home/rsg/ltib/rpm' --define '_prefix /usr' --define
> '_tmppath /home/rsg/ltib/tmp' --define '_rpmdir /home/rsg/ltib/rpm/RPMS'
> --define '_mandir /usr/share/man' --define '_sysconfdir /etc' --define
> '_localstatedir /var' -bb --clean
> --rmsource  /home/rsg/ltib/rpm/SPECS/kernel-2.6.22-uc1.spec
> Building target platforms: m68knommu
> Building for target m68knommu
> Executing(%prep): /bin/sh -e /home/rsg/ltib/tmp/rpm-tmp.76918
> + umask 022
> + cd /home/rsg/ltib/rpm/BUILD
> + exit 0
> Executing(%build): /bin/sh -e /home/rsg/ltib/tmp/rpm-tmp.76918
> + umask 022
> + cd /home/rsg/ltib/rpm/BUILD
> + exit 0
> Executing(%install): /bin/sh -e /home/rsg/ltib/tmp/rpm-tmp.76918
> + umask 022
> + cd /home/rsg/ltib/rpm/BUILD
> Processing files: kernel-2.6.22-uc1
> error: File not found by
> glob: /home/rsg/ltib/tmp/kernel/opt/freescale/rootfs/m68knommu/*
> 
> 
> RPM build errors:
>     File not found by
> glob: /home/rsg/ltib/tmp/kernel/opt/freescale/rootfs/m68knommu/*
> Build time for kernel-2.6.22-uc1: 0 seconds
> 
> Failed building kernel-2.6.22-uc1
> 
> 
> f_buildrpms() returned an error, exiting
> traceback:
>  main:557
> 
> 
> Started: Wed Apr 15 21:36:38 2009
> Ended:   Wed Apr 15 21:36:53 2009
> Elapsed: 15 seconds
> 
> These packages failed to build:
> kernel-2.6.22-uc1 
> Build Failed
> 
> Exiting on error or interrupt
> 
> Any ideas?
> 
> Thanks,
> -Bob
> 
> 
> 
> 
> _______________________________________________
> LTIB home page: http://bitshrine.org
> 
> Ltib mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/ltib
> 


_______________________________________________
LTIB home page: http://bitshrine.org

Ltib mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/ltib