ltib
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Ltib] Problem while running Dillo2 browser on latest CVS LTIB code


From: Hamilton Vera
Subject: Re: [Ltib] Problem while running Dillo2 browser on latest CVS LTIB code + IMX27 ADS board.
Date: Mon, 28 Dec 2009 17:24:02 -0200

Here is what we use to startx :

#!/bin/sh

module=`lsmod | grep mxc_ts`
if [ ! "$module" ]; then
        modprobe mxc_ts;
fi

module=`lsmod | grep ehci_hcd`
if [ ! "$module" ]; then
        modprobe ehci_hcd;
fi

export TSLIB_CONSOLEDEVICE=none
export TSLIB_TSDEVICE=/dev/input/event1

echo "nameserver 208.67.220.220" > /etc/resolv.conf

if [ ! -e /dev/tty0 ]; then ln -s /dev/vc/0 /dev/tty0; fi
if [ ! -e /dev/tty1 ]; then ln -s /dev/vc/1 /dev/tty1; fi
if [ ! -e /dev/tty2 ]; then ln -s /dev/vc/2 /dev/tty2; fi

Xfbdev -screen 240x320x60  -mouse tslib,,device=/dev/input/event1 &
sleep 3

# Start woosh internet browser.
#DISPLAY=:0 /usr/bin/woosh

# Start dillo internet browser.
DISPLAY=:0 /usr/bin/dillo
# Stops the X.
#killall Xfbdev


[]'s

Hamilton Vera



On Mon, Dec 28, 2009 at 11:31 AM, Stuart Hughes <address@hidden> wrote:
> Hi Rajesh,
>
> If you have the latest Savannah CVS startx should be in the path (on the
> host): rootfs/usr/bin/startx, this contains:
>
> #!/bin/sh
>
> Xfbdev -ac -mouse mouse -keybd keyboard &
> sleep 3
> DISPLAY=:0 twm
> killall Xfbdev
>
> Regards, Stuart
>
> Rajesh Marathe wrote:
>>
>> Stuart,
>>
>> Thanks. I think I did not start X server earlier. I had compiled LTIB
>> with X Server option but did not find "startx" under rootfs on the
>> device. How to get the X started on the device ?
>>
>> regards,
>> Rajesh Marathe.
>>
>> On Mon, 2009-12-28 at 10:54 +0000, Stuart Hughes wrote:
>>>
>>> Hi Rajesh,
>>>
>>> I don't have that board so can't look.  However, make sure you have
>>> started the X server (with startx) first.  Also make sure you have the
>>> framebuffer enabled in the kernel (it should be I think).
>>>
>>> Regards, Stuart
>>>
>>> Rajesh Marathe wrote:
>>>>
>>>> Hi,
>>>>
>>>> We are working on IMX27 ADS board and have taken latest CVS based LTIB
>>>> code. I have included 'Dillo2' and 'fltk' packages as my objective would
>>>> be to run the browser dillo on the imx27 system.
>>>>
>>>> After the Linux boots up, I go to the console and try to run the
>>>> browser. But, I get the following error:
>>>>
>>>> ----------------------------------------------------------------------
>>>> mx27#
>>>>         mx27#
>>>>             mx27# ./dillo
>>>>                 paths: Cannot open file
>>>> '//.dillo/dillorc'                                      paths:
>>>> Using /usr/etc/dillo/dillorc
>>>> paths: Cannot open file
>>>> '//.dillo/keysrc'                                       paths:
>>>> Using /usr/etc/dillo/keysrc
>>>>  dillo_dns_init: Here we go!
>>>> (threaded)                                          Disabling
>>>> cookies.
>>>>  Can't open display
>>>> ":0.0"                                                       mx27#
>>>> ----------------------------------------------------------------------
>>>>
>>>> I did try to debug and found out that the function fltk::open_display
>>>> returns the above display error.
>>>>
>>>> How do I set the display correctly so that the browser's opening page
>>>> gets displayed on the LCD panel connected to IMX27 board ?
>>>>
>>>> regards,
>>>> Rajesh Marathe.
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> LTIB home page: http://ltib.org
>>>>
>>>> Ltib mailing list
>>>> address@hidden
>>>> http://lists.nongnu.org/mailman/listinfo/ltib
>>>>
>>
>>
>
>
> _______________________________________________
> LTIB home page: http://ltib.org
>
> Ltib mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/ltib
>



-- 
Hamilton Vera
int Administrator (char Network[],char ComputationalSystems[])
http://hvera.wordpress.com




reply via email to

[Prev in Thread] Current Thread [Next in Thread]