[Openvortex-dev] Re: au88x0 modem

[Raymond]

Philipp Matthias Hahn wrote:
> Hello!
>
> On Tue, Sep 13, 2005 at 08:35:29PM +0300, Sasha Khapyorsky wrote:
>
> > On 10:55 Tue 13 Sep     , Philipp Matthias Hahn wrote:
> >
> > > See attached tar-file for a full copy of everything under
> > > /proc/asound/au8810 after applying the attached patch against ASLA from
> > > linux-2.6.13.1.
> >
> > ac97#0-N entries are identical there for both codecs, this is because
> > ac97_codec_read/write always accesses primary codec. Try next patch
> > please.
> >
> > --- au88x0_core.c_orig  2005-09-13 20:00:50.000000000 +0300
> > +++ au88x0_core.c       2005-09-13 20:05:36.000000000 +0300
> > @@ -2535,7 +2535,8 @@ vortex_codec_write(ac97_t * codec, unsig
> >         }
> >         /* write register */
> >         hwwrite(card->mmio, VORTEX_CODEC_IO,
> > -               ((addr << VORTEX_CODEC_ADDSHIFT) & VORTEX_CODEC_ADDMASK) |
> > +               (((addr << VORTEX_CODEC_ADDSHIFT) & VORTEX_CODEC_ADDMASK) |
> > +                ((0x80*codec->num) << VORTEX_CODEC_ADDSHIFT)) |
> >                 ((data << VORTEX_CODEC_DATSHIFT) & VORTEX_CODEC_DATMASK) |
> >                 VORTEX_CODEC_WRITE);
> >
> > @@ -2560,6 +2561,7 @@ static unsigned short vortex_codec_read(
> >         }
> >         /* set up read address */
> >         read_addr = ((addr << VORTEX_CODEC_ADDSHIFT) & VORTEX_CODEC_ADDMASK);
> > +       read_addr |= (0x80*codec->num) << VORTEX_CODEC_ADDSHIFT ;
> >         hwwrite(card->mmio, VORTEX_CODEC_IO, read_addr);

#define VORTEX_CODEC_WRITE      0x00800000
#define VORTEX_CODEC_ADDSHIFT   16

(0x80* 1) << VORTEX_CODEC_ADDSHIFT)  is equal to  VORTEX_CODEC_WRITE

May be au8810 use different set of MMIO to read/write and report
status of the audio codec and modem codec ?

au8810.h

#define VORTEX_MODEM_CTRL       0x291ac

Make sure you have a BACKUP of all your data before you peform testing
on the modem.

It's not easy to hack the modem since we don't have any datasheet of 
au8810 and MOT6269353. (AC-link between them)

> ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> 
> IRQ 10
> Vortex: init.... <6>done.
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> AC'97 1 does not respond - RESET
> vortex: ac97 address never arrived
> vortex: ac97 address never arrived
> AC'97 1 access is not valid [0xffffffff], removing mixer.
> Vortex: shutdown...vortex: FATAL: ResManager: resource type 3 exhausted.
> vortex: FATAL: ResManager: resource type 3 exhausted.
> vortex_adb_delroutes: route not found! 0x24a0
> src alarm
> vortex_adb_delroutes: route not found! 0x24a1
> src alarm
> vortex_adb_delroutes: route not found! 0x7e88
> vortex_adb_delroutes: route not found! 0x7f89
> vortex: FATAL: ResManager: resource type 2 exhausted.
> vortex: FATAL: ResManager: resource type 2 exhausted.
> vortex_adb_delroutes: route not found! 0x7044
> vortex_adb_delroutes: route not found! 0x7144
> vortex: FATAL: ResManager: resource type 3 exhausted.
> vortex: FATAL: ResManager: resource type 3 exhausted.
> vortex_adb_delroutes: route not found! 0x2492
> src alarm
> vortex_adb_delroutes: route not found! 0x2493
> src alarm
> done.
> ACPI: PCI interrupt for device 0000:00:06.0 disabled
> au8810: probe of 0000:00:06.0 failed with error -5
>
> BYtE
> Philipp