qemu-arm
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Qemu-arm] [Qemu-devel] [PATCH V3 2/2] arm_gicv3_kvm: kvm_dist_get/p


From: Peter Maydell
Subject: Re: [Qemu-arm] [Qemu-devel] [PATCH V3 2/2] arm_gicv3_kvm: kvm_dist_get/put: skip the registers banked by GICR
Date: Thu, 24 May 2018 15:56:37 +0100

On 24 May 2018 at 15:40, Auger Eric <address@hidden> wrote:
> Hi Peter,
>
> On 05/24/2018 04:16 PM, Peter Maydell wrote:
>> Only for KVM, not for TCG, and it's the other way round: we
>> end up with two lots of PPI/SGI space in the data structure
>> by mistake. Let me fish out the comment I made on the v2 of this
>> series:
>>
>> In the code in master, we have QEMU data structures
>> (bitmaps, etc) which have one entry for each of GICV3_MAXIRQ
>> irqs. That includes the RAZ/WI unused space for the SPIs/PPIs, so
>> for a 1-bit-per-irq bitmap:
>>  [0x00000000, irq 32, irq 33, .... ]
>>
>> When we fill in the values from KVM into these data structures,
>> we start after the unused space, because the for_each_dist_irq_reg()
>> macro starts with _irq = GIC_INTERNAL. But we forgot to adjust
>> the offset value we use for the KVM access, so we start by
>> reading the RAZ/WI values from KVM, and the data structure
>> contents end up with:
>>  [0x00000000, 0x00000000, irq 32, irq 33, ... ]
>> (and the last irqs wouldn't get transferred).
> In kvm_dist_get_priority (new code), the offset is where we read and
> field is where we write, correct? Offset was shifted so we effectively
> read in KVM regs the num_irq-32 SPI states now but don't we start
> writing at the beginning of bmp, (ie s->gicd_ipriority), at PPI/SGI
> offset? What am I missing?

Oops, yes, you're right. My explanation applies to the
various other bitmaps, where we are accessing the
fields in the data structure using gic_bmp_ptr32(bmp, irq),
but not to gicd_ipriority[], which we are directly accessing
starting with the first word, not by indexing via bmp[irq].

So we need to handle these two cases differently.
You're correct that for gicd_ipriority[], the code in
master reads and writes to that data structure as:
 [0, 0, ..., 0, irq 32, irq 33, ..., 0, 0, ... 0]
so all the values are in the right place but we:
 (a) unnecessarily read/write zeroes for the PPI/SGI fields
 (b) fail to transfer the last 32 interrupts

We can fix the gicd_ipriority[] case simply by adding
   bmp = GIC_INTERNAL;
before the assignment to 'field' in both kvm_dist_get_priority()
and kvm_dist_put_priority(). This doesn't affect migration
compatibility. We should do this separately from fixing the
other bitmaps, because it's simpler.

> I don't understand you TCG remark above, sorry.

You can migrate a TCG VM as well as a KVM one. The
TCG GICv3 doesn't use any of this code in hw/intc/arm_gicv3_kvm.c,
so it doesn't have any of these bugs. So any fixups for the
KVM bugs so we get migration correct in the
"buggy VM" -> "not buggy VM" situation should not misidentify
a TCG VM as "buggy".

PS: I have a feeling that kvm_dist_get/set_priority have
an endianness problem -- the 'reg' we read from the kernel
will be a 32-bit value with the priority byte for the
lowest-numbered IRQ in its least significant byte, but if
the host is big-endian we'll write that to the wrong offset
in the gicd_priority[] array...

thanks
-- PMM



reply via email to

[Prev in Thread] Current Thread [Next in Thread]