[Qemu-devel] Re: option-rom (was cg14)

[Bob Breuer]

Blue Swirl wrote:
> On Fri, Jun 4, 2010 at 5:40 PM, Artyom Tarasenko
> <address@hidden> wrote:
>   
>>>>> 2010/5/27 Bob Breuer <address@hidden>:
>>>>> +    /* DBRI (audio) */
>>>>> +    cpu_register_physical_memory_offset(0xEE0001000ULL, 0x10000, 
>>>>> bad_mem, 0xE0001000);
>>>>>           
>>>> Please add a new DBRI device ;-).
>>>>         
>>> Or maybe just a field in hwdef + empty_slot? :-)
>>>       
>> Or actually don't bother at all. What is expected at 0xee0001000 is
>> not the DBRI device, but its FCode driver.
>> I wrote a stub, but don't see that it helps to boot except one has a
>> nice device name (
>>
>> Probing /obio at 2,0  cgfourteen
>> Probing /address@hidden,e0000000/address@hidden,e0001000 at f,0  espdma esp 
>> sd st
>> ledma le SUNW,bpp
>> Probing /address@hidden,e0000000/address@hidden,e0001000 at e,0  
>> qemu,device-stub
>> Probing /address@hidden,e0000000/address@hidden,e0001000 at 0,0  Nothing 
>> there
>>
>>  ) and switching off slot "e" probing is not necessary.
>>
>>
>> What would be nice is a generic '-option-rom' switch which would take
>> a rom address and rom file or contents
>> as params. Or do we have something like this? I mean for qemu-system-sparc.
>>     
>
> Maybe SysBusDeviceInfo should have something similar to PCI .romfile
> field, or we should rather have a SBusDeviceInfo. That way ROM
> handling would be automatic.
>   

With empty_slot SS-20 OBP accesses just 2 addresses for slot E:
    0xEE0001000 - 8bit read (FCode)
    0xEE0010000 - 32bit write (put DBRI into reset)

Did a little digging, slot E starts at 0xEE0000000 (0xE << 32 | slot <<
28).  On my SS-20, the DBRI FCode is only 48 bytes which is then
mirrored every 64 bytes within at least the first 8K, and the actual
registers are at offset 64K with a reported length of 256 bytes.

Besides hooking up DBRI (empty_slot or not), I would propose the
following additions to the sun4m_hwdef structure so that the other
missing pieces can then be hooked up to empty_slot.

--- a/hw/sun4m.c
+++ b/hw/sun4m.c
@@ -98,6 +98,10 @@ struct sun4m_hwdef {
     target_phys_addr_t serial_base, fd_base;
     target_phys_addr_t afx_base, idreg_base, dma_base, esp_base, le_base;
     target_phys_addr_t tcx_base, cs_base, apc_base, aux1_base, aux2_base;
+    target_phys_addr_t dbri_base, sx_base;
+    struct {
+        target_phys_addr_t reg_base, vram_base;
+    } vsimm[4];
     target_phys_addr_t ecc_base;
     uint32_t ecc_version;
     uint8_t nvram_machine_id;

Also, looks like OpenBIOS would need some additional ranges added under
obio and sbus.  From a SS-20:
ok cd /obio
ok .attributes
ranges                   00000000  00000000  0000000f  f1000000  01000000
                         00000001  00000000  00000000  90000000  04000000
                         00000002  00000000  00000000  9c000000  04000000
                         00000003  00000000  00000000  f0000000  04000000
                         00000004  00000000  00000000  fc000000  04000000
device_type              hierarchical
name                     obio
ok cd /iommu/sbus
ok .attributes
clock-frequency          017d7840
scsi-initiator-id        00000007
burst-sizes              00f8007f
ranges                   00000000  00000000  0000000e  00000000  10000000
                         00000001  00000000  0000000e  10000000  10000000
                         00000002  00000000  0000000e  20000000  10000000
                         00000003  00000000  0000000e  30000000  10000000
                         0000000e  00000000  0000000e  e0000000  10000000
                         0000000f  00000000  0000000e  f0000000  10000000
address                  ffeec000
reg                      0000000f  e0001000  00000020
slot-address-bits        0000001c
up-burst-sizes           0000003f
device_type              hierarchical
name                     sbus