Re: [Qemu-devel] [PATCH 6/9] vhost-scsi: new device supporting the tcm_vhost Linux kernel module

[Libaiqing]

Hi Asias,

> -----Original Message-----
> From: Asias He [mailto:address@hidden
> Sent: Thursday, June 20, 2013 5:39 PM
> To: Libaiqing
> Cc: Paolo Bonzini; Wenchao Xia; address@hidden;
> address@hidden; Michael S. Tsirkin; Haofeng
> Subject: Re: [Qemu-devel] [PATCH 6/9] vhost-scsi: new device supporting the
> tcm_vhost Linux kernel module
> 
> On Thu, Jun 20, 2013 at 08:49:50AM +0000, Libaiqing wrote:
> > Hi Asias,
> >     Thanks for your config.
> >     According to you config,I test booting from vhost device with
> upstream kernel and qemu,but failed.
> >
> >     1 installing guest from cdrom,ok.
> >     2 booting vhost-scsi,guest fs error occurs.
> >     3 using fileio backstores,the error is same..
> >     4 rebooting guest,a log printed:
> >      (qemu) hw/scsi/virtio-scsi.c:533:virtio_scsi_handle_event: Object
> 0x7fccae7f2c88 is not an instance of type virtio-scsi-device
> 
> Paolo, I remember you fixed a similar issue?
> 
> >     5 using upstream seabios,core dumped.
> >
> >     Could you give me some advise to debug this problem ? I can provide
> more information if need.
> 
> Can you show me qemu commit id you used? Can you verity that if using the
> host kernel for guest helps? Does booting directly (without the install
> and reboot process) work?
Qemu commit id is "commit 4eda32f588086b6cd0ec2be6a7a6c131f8c2b427".

Guest kernel updateing is useless.

Booting directly doesn't work too.


> > The qemu cmd:
> > address@hidden x86_64-softmmu]# ./qemu-system-x86_64 -enable-kvm
> -name fedora   -M pc -m 1024 -smp 2   -drive
> file=/home/fedora18.iso,if=ide,media=cdrom -device
> vhost-scsi-pci,wwpn=naa.50014057133e25dc  -monitor stdio   -vga qxl
> -vnc :1
> >
> > The vnc output:
> > Dracut-initqueue[189]:/dev/mapper/fedora-root:UNEXPECTED
> INCONSISTENCY;RUN FSCK MANUALLY.
> > Dracut-initqueue[189]: Warning: e2fsck returned with 4
> > Dracut-initqueue[189]: Warning: ***An error occurred during the file
> system check.
> >
> > The guest kernel log:
> > Kernel: virtio-pci 0000:00:04.0: irq 40 for MSI/MSI-X
> > Kernel: virtio-pci 0000:00:04.0: irq 41 for MSI/MSI-X
> > Kernel: virtio-pci 0000:00:04.0: irq 42 for MSI/MSI-X
> > Kernel: virtio-pci 0000:00:04.0: irq 43 for MSI/MSI-X
> > Kernel: scsi2 : Virtio SCSI HBA
> > Kernel: scsi 2:0:1:0: Direct-Access LIO-ORG r0
> > Kernel: sd 2:0:1:0: Attached scsi generic sg1 type 0
> > Kernel: sd 2:0:1:0: [sda]1258912 512-byte logical .....
> > Kernel: sd 2:0:1:0: [sda]write protect is off
> > Kernel: sd 2:0:1:0: [sda]Mode sense :43 00 00 08
> > Kernel: sd 2:0:1:0: [sda]write cache: disabled, read .....
> > Kernel: sda sda1 sda2
> > Kernel: sd 2:0:1:0: [sda] Attached SCSI disk
> > Dracut-initqueue[189]: Scanning devices sda2 for LVM
> > Dracut-initqueue[189]: inactive '/dev/fedora/swap'...
> > Dracut-initqueue[189]: inactive '/dev/fedora/root'...
> >
> > The info of host:
> > address@hidden x86_64-softmmu]# uname -a
> > Linux fedora121 3.10.0-rc6 #1 SMP Wed Jun 19 19:34:24 CST 2013 x86_64
> x86_64 x86_64 GNU/Linux
> > address@hidden x86_64-softmmu]# lsmod |grep vhost_scsi
> > vhost_scsi             49456  5
> > target_core_mod       282163  14
> target_core_iblock,target_core_pscsi,iscsi_target_mod,target_core_file,vh
> ost_scsi
> > address@hidden x86_64-softmmu]# targetcli
> > targetcli shell version v2.1.fb26
> > Copyright 2011 by RisingTide Systems LLC and others.
> > For help on commands, type 'help'.
> >
> > /> ls
> > o-
> / 
> ..............................................................................................................
> ........... [...]
> >   o-
> backstores 
> ...............................................................................................
> ............... [...]
> >   | o-
> block 
> ..................................................................................................
> [Storage Objects: 0]
> >   | o-
> fileio 
> .................................................................................................
> [Storage Objects: 0]
> >   | o-
> pscsi 
> ..................................................................................................
> [Storage Objects: 0]
> >   | o-
> ramdisk 
> ................................................................................................
> [Storage Objects: 1]
> >   |   o-
> r0 
> ...................................................................................................
> [(6.0GiB) activated]
> >   o-
> iscsi 
> .........................................................................................................
> ... [Targets: 0]
> >   o-
> loopback 
> ..................................................................................................
> ....... [Targets: 0]
> >   o-
> vhost 
> .......................................................................................................
> ..... [Targets: 1]
> >     o-
> naa.50014057133e25dc 
> ............................................................................
> .................. [TPGs: 1]
> >       o-
> tpg1 
> ...............................................................................................
> [naa.5001405a70ac3421]
> >         o-
> acls 
> ..........................................................................................................
> [ACLs: 0]
> >         o-
> luns 
> ..........................................................................................................
> [LUNs: 1]
> >           o-
> lun0 
> .....................................................................................................
> [ramdisk/r0]
> >
> > Regards,
> > baiqing
> > > -----Original Message-----
> > > From: Asias He [mailto:address@hidden
> > > Sent: Thursday, June 20, 2013 9:34 AM
> > > To: Libaiqing
> > > Cc: Paolo Bonzini; Wenchao Xia; address@hidden;
> > > address@hidden; Michael S. Tsirkin; Haofeng
> > > Subject: Re: [Qemu-devel] [PATCH 6/9] vhost-scsi: new device supporting
> the
> > > tcm_vhost Linux kernel module
> > >
> > > On Wed, Jun 19, 2013 at 12:55:10PM +0000, Libaiqing wrote:
> > > > Hi paolo,
> > > >   The vhost-scsi device can be used as boot device?
> > > >   I tested with your config + 3.10 rc6 + seabios 1.7.2.2,but failed.
> > > >   Could you give me some advise to debug this problem ? I can
> provide
> > > more information if need.
> > >
> > > Boot from vhost-scsi is supposed to work. The seabios you used should
> be
> > > fine which contains the fixes for vhost-scsi.
> > >
> > > Instead of playing with the /sys/kernel/config/target directly, I really
> > > recommend using targetcli utils.
> > >
> > > Nab, I think we really should write some docs for people to use
> > > vhost-scsi.
> > >
> > > This is how I install and use targetcli in RHEL6. Note you need upstream
> > > kernel and qemu bits for vhost-scsi.
> > >
> > > # yum groupinstall  'Development tools'
> > > # yum install python-devel epydoc python-simpleparse
> > >
> > > # git clone git://github.com/agrover/rtslib-fb.git
> > > # git clone git://github.com/agrover/targetcli-fb.git
> > > # git clone git://github.com/agrover/configshell-fb.git
> > > # for i in rtslib-fb configshell-fb targetcli-fb; do
> > >           make -C $i rpm
> > >           yum localinstall $i/dist/*.noarch.rpm
> > >   done
> > >
> > > In targetcli, create a backstore and vhost wwpn, e.g.
> > > # targetcli
> > > /> /backstores/ramdisk create r0 1g
> > > /> /vhost create
> > > /> cd /vhost/naa.500140527cb6616b/tpg1/luns
> > > /> create /backstores/ramdisk/r0
> > >
> > > # qemu -device vhost-scsi-pci,wwpn=naa.500140527cb6616b ...
> > >
> > > Hope this helps.
> > >
> > > > Regards,
> > > > baiqing
> > > >
> > > > > -----Original Message-----
> > > > > From: address@hidden
> > > > > [mailto:address@hidden
> On
> > > > > Behalf Of Paolo Bonzini
> > > > > Sent: Tuesday, May 28, 2013 4:01 PM
> > > > > To: Wenchao Xia
> > > > > Cc: address@hidden; address@hidden;
> address@hidden;
> > > > > Michael S. Tsirkin
> > > > > Subject: Re: [Qemu-devel] [PATCH 6/9] vhost-scsi: new device
> supporting
> > > the
> > > > > tcm_vhost Linux kernel module
> > > > >
> > > > > Il 28/05/2013 09:13, Wenchao Xia ha scritto:
> > > > > >> > From: Nicholas Bellinger <address@hidden>
> > > > > >> >
> > > > > >> > The WWPN specified in configfs is passed to "-device
> > > vhost-scsi-pci".
> > > > > >> > The tgpt field of the SET_ENDPOINT ioctl is obsolete now, so it 
> > > > > >> > is
> not
> > > > > >> > available from the QEMU command-line.  Instead, I hardcode it
> to
> > > > > zero.
> > > > > >> >
> > > > > > Hi, Paolo
> > > > > >   Any document about how to config it correctly in configfs,
> before
> > > > > > invoking qemu with the WWPN number?
> > > > >
> > > > > Unfortunately no, but vhost-scsi doesn't have many knobs (unlike
> > > > > iSCSI for example) so it's quite simple.  Here is an example:
> > > > >
> > > > > cd /sys/kernel/config/target
> > > > > mkdir -p core/fileio_0/fileio
> > > > > echo
> > > 'fd_dev_name=/home/pbonzini/test.img,fd_dev_size=5905580032' >
> > > > > core/fileio_0/fileio/control
> > > > > echo 1 > core/fileio_0/fileio/enable
> > > > > mkdir -p vhost/naa.600140554cf3a18e/tpgt_0/lun/lun_0
> > > > > cd vhost/naa.600140554cf3a18e/tpgt_0
> > > > > ln -sf ../../../../../core/fileio_0/fileio/ 
> > > > > lun/lun_0/virtual_scsi_port
> > > > > echo naa.60014053226f0388 > nexus
> > > > >
> > > > > The "nexus" value is the initiator WWN.  naa.600140554cf3a18e is
> the
> > > > > target WWN that you have to pass to "-device vhost-scsi-pci".
> > > > >
> > > > > Paolo
> > > >
> > >
> > > --
> > > Asias
> 
> --
> Asias