[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] Customizing ARM Emulation boards?
From: |
Alexander Duff |
Subject: |
[Qemu-devel] Customizing ARM Emulation boards? |
Date: |
Thu, 14 Apr 2016 13:03:42 -0400 |
User-agent: |
Mozilla/5.0 (X11; Linux x86_64; rv:38.0) Gecko/20100101 Thunderbird/38.6.0 |
Hello,
(This is cross-posted from the general discussion mailing list)
I'm emulating routers running OpenWrt for ARM using the
realview-eb-mpcore machine and I've run into the problem of not being
able to create more than one NIC. For what it's worth, when specifying
that the NIC should be an smc91c111, qemu-system-arm -M
realview-eb-mpcore says that this machine doesn't support that device.
When the device is unspecified, it defaults to the smc91c111 once the
machine is booted. Every NIC after the first defaults to rtl8139, but
emulation of the PCI bus is missing (I am unsure if it's missing due to
the OpenWrt kernel built for ARM or something in QEMU) so these devices
show in QEMU's monitor, but not on the guest. Since it's a router, I
would very much like to have more than one ethernet port. I downloaded
the QEMU source and looked through it to see how the devices are created
and assigned. In realview.c (lines 265 through 281), I found the
following code:
for(n = 0; n < nb_nics; n++) {
nd = &nd_table[n];
if (!done_nic && (!nd->model ||
strcmp(nd->model, is_pb ? "lan9118" : "smc91c111") == 0)) {
if (is_pb) {
lan9118_init(nd, 0x4e000000, pic[28]);
} else {
smc91c111_init(nd, 0x4e000000, pic[28]);
}
done_nic = 1;
} else {
if (pci_bus) {
pci_nic_init_nofail(nd, pci_bus, "rtl8139", NULL);
}
}
}
So my understanding is that it checks to see if a NIC has been created.
If it hasn't, it creates an smc91c111 NIC and maps it to 0x4e000000,
then sets "done_nic" to 1 and creates all subsequent NICs as rtl8139
devices.
So, I have the following questions:
1) Could I make my own customized board by more-or-less copying the
realview.c file and changing this section so that the first 8 or so NICs
(however many I can fit in that memory space) are smc91c111 devices and
offset them by the space it takes (I want to say 16 but I'll double
check first)? The next address on the memory map is 0x4f00000000 (USB,
which I don't need anyway).
2) Is there any documentation on programming a custom board? In this
case, I don't think I need it, but it would be good to have. I apologize
if I've missed it, there are a lot of moving parts in this endeavor.
3) Is there a simpler way to get more than one ethernet port on a
virtualized ARM machine? I've been working on this for a long time and
I'm afraid I'm getting tunnel vision and missing an obvious solution.
4) Is this the right mailing list?If there's a better place to ask this
question or if anyone can point me in the right direction, I would be
grateful for that information. I already posted on the OpenWrt forums
and received 0 replies.
Thank you very much, and I appreciate any help I can get on this.
-Alex
- [Qemu-devel] Customizing ARM Emulation boards?,
Alexander Duff <=