qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PULL 35/40] migration/qmp: add command migrate-pause


From: Juan Quintela
Subject: [Qemu-devel] [PULL 35/40] migration/qmp: add command migrate-pause
Date: Wed, 16 May 2018 01:40:12 +0200

From: Peter Xu <address@hidden>

It pauses an ongoing migration.  Currently it only supports postcopy.
Note that this command will work on either side of the migration.
Basically when we trigger this on one side, it'll interrupt the other
side as well since the other side will get notified on the disconnect
event.

However, it's still possible that the other side is not notified, for
example, when the network is totally broken, or due to some firewall
configuration changes.  In that case, we will also need to run the same
command on the other side so both sides will go into the paused state.

Reviewed-by: Dr. David Alan Gilbert <address@hidden>
Signed-off-by: Peter Xu <address@hidden>
Message-Id: <address@hidden>
Signed-off-by: Juan Quintela <address@hidden>

---
s/2.12/2.13/
---
 migration/migration.c | 29 +++++++++++++++++++++++++++++
 qapi/migration.json   | 16 ++++++++++++++++
 2 files changed, 45 insertions(+)

diff --git a/migration/migration.c b/migration/migration.c
index 3deded90e5..05aec2c905 100644
--- a/migration/migration.c
+++ b/migration/migration.c
@@ -1507,6 +1507,35 @@ void qmp_migrate_recover(const char *uri, Error **errp)
     qemu_start_incoming_migration(uri, errp);
 }
 
+void qmp_migrate_pause(Error **errp)
+{
+    MigrationState *ms = migrate_get_current();
+    MigrationIncomingState *mis = migration_incoming_get_current();
+    int ret;
+
+    if (ms->state == MIGRATION_STATUS_POSTCOPY_ACTIVE) {
+        /* Source side, during postcopy */
+        qemu_mutex_lock(&ms->qemu_file_lock);
+        ret = qemu_file_shutdown(ms->to_dst_file);
+        qemu_mutex_unlock(&ms->qemu_file_lock);
+        if (ret) {
+            error_setg(errp, "Failed to pause source migration");
+        }
+        return;
+    }
+
+    if (mis->state == MIGRATION_STATUS_POSTCOPY_ACTIVE) {
+        ret = qemu_file_shutdown(mis->from_src_file);
+        if (ret) {
+            error_setg(errp, "Failed to pause destination migration");
+        }
+        return;
+    }
+
+    error_setg(errp, "migrate-pause is currently only supported "
+               "during postcopy-active state");
+}
+
 bool migration_is_blocked(Error **errp)
 {
     if (qemu_savevm_state_blocked(errp)) {
diff --git a/qapi/migration.json b/qapi/migration.json
index da351d7421..23ba85ed3a 100644
--- a/qapi/migration.json
+++ b/qapi/migration.json
@@ -1211,3 +1211,19 @@
 ##
 { 'command': 'migrate-recover', 'data': { 'uri': 'str' },
   'allow-oob': true }
+
+##
+# @migrate-pause:
+#
+# Pause a migration.  Currently it only supports postcopy.
+#
+# Returns: nothing.
+#
+# Example:
+#
+# -> { "execute": "migrate-pause" }
+# <- { "return": {} }
+#
+# Since: 2.13
+##
+{ 'command': 'migrate-pause', 'allow-oob': true }
-- 
2.17.0




reply via email to

[Prev in Thread] Current Thread [Next in Thread]