[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Discuss-gnuradio] Re: USB2 problems with Fedora/USRP
From: |
Alberto Trentadue |
Subject: |
[Discuss-gnuradio] Re: USB2 problems with Fedora/USRP |
Date: |
Sat, 17 Jan 2009 11:54:27 +0100 (CET) |
>----Messaggio originale----
>Da: address@hidden
>Data: 15/01/2009 22.37
>A: "Discuss GNU Radio List"
<address@hidden>
>Ogg: [Discuss-gnuradio] Re: USB2 problems with Fedora/USRP
>
>> Hello
>>
>...
>> The next
step is to try out some example, e.g. usrp_benchmark_usb.py or usrp_wfm_rcv.py.
>> Whatever
>the test I try, I can see
that blinking led is switched of for a couple seconds, then it blinks at lower
>> rate, and
>another led near to it
turns on (don't remember which is D402 and D403).
>>
>> On console, i get this kind of error:
>>
>
>>
usb_control_msg failed: error sending control message: Connection timed out
>> usrp: failed to load fpga bitstream
>/opt/gnuradio/share/usrp/rev4/std_2rxhb_2tx.rbf
>> Traceback (most recent call last):
>> File ".
/usrp_benchmark_usb.
>py", line 106, in ?
>> main ( )
>> File "./usrp_benchmark_usb.py", line 96, in main
>> ok=run_test
>(rate, verbose)
>> File "./usrp_benchmark_usb.py", line 63, in run_test
>>
usrp_tx=usrp.sink_s(0, tx_interp)
>
>> File
>> "/usr/local/hamradio/gnuradio/lib/python2.5/site-packages/gnuradio/usrp.
py", line 230, in __init__
>>
>fpga_filename, firmware_filename)
>> File
"/usr/local/hamradio/gnuradio/lib/python2.5/site-packages/gnuradio/usrp1.
>py", line 940, in sink_s
>> return
_usrp1.sink_s(*args)
>> RuntimeError: can't open usrp1
>...
>==== Eric Blossom
>wrote
>
>>Confirm that your computer
has an EHCI host controller.
>...
>=====
>
>Hello
>
>The PC has the EHCI host controller:
>
>
>address@hidden usb]# lspci
>...
>00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
>Controller #2
>(rev 03)
>
>Now, I've
tried again launching the usrp_benchmark_usb.py and then
>address@hidden usb]# cat
>/proc/bus/usb/devices
>...
>T:
Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
>D: Ver= 2.00 Cls=ff(vend.)
>Sub=ff Prot=ff MxPS=64
#Cfgs= 1
>P: Vendor=fffe ProdID=0002 Rev= 1.04
>S: Manufacturer=Free Software Folks
>S:
>Product=USRP Rev 4
>S:
SerialNumber=480f9a8a
>C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
>I:* If#= 0 Alt= 0 #EPs= 0 Cls=ff
>(vend.) Sub=ff Prot=ff
Driver=(none)
>I:* If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
>E: Ad=02(O)
>Atr=02(Bulk) MxPS=
512 Ivl=0ms
>I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
>E: Ad=86(I) Atr=02
>(Bulk) MxPS=
512 Ivl=0ms
>
>It seems that I was wrong: USB2 driver seems to be working well, at least for
>the first
>configuration
steps, because I am successful in configuring the Cypress FX2.
>Then it looks like the problem is actually
>in the
next step, that is, loading the fpga bitstream
/usr/local/hamradio/gnuradio/share/usrp/rev4/std_2rxhb_2tx.rbf
>
Hello
After some more investigation and code inspection, it turns out that I managed
to load the FPGA (I guess...) but the
weird thing is that I achieved that by changing the source code in in
/gnuradio/usrp/host/lib/legacy/usrp_prims.cc now
the FPGA load succeeds
...
// reset FPGA (and on rev1 both AD9862's, thus killing clock)
usrp_set_fpga_reset (udh,
1); // hold fpga in reset
if (write_cmd (udh, VRQ_FPGA_LOAD, 0, FL_BEGIN, 0, 0) != 0)
goto fail;
while ((n
= fread (buf, 1, sizeof (buf), fp)) > 0){
if (write_cmd (udh, VRQ_FPGA_LOAD, 0, FL_XFER, buf, n) != n)
goto
fail;
}
//IZ0CEZ_DEBUG
fprintf (stderr, "iz0cez_debug: added printout, delay?\n"); //<== PRINTOUT??
if
(write_cmd (udh, VRQ_FPGA_LOAD, 0, FL_END, 0, 0) != 0)
goto fail;
fclose (fp);
...
I could verify that by
using usrper:
address@hidden rev4]# usrper load_firmware std.ihx
usrper: found unconfigured usrp; needs firmware.
address@hidden rev4]# usrper load_fpga std_2rxhb_2tx.rbf
iz0cez_debug: added printout, delay?
address@hidden rev4]#
Why?
May this indicate a timing issue in the USB2 connection? How may investigate
(and possibly fix or workaround) USB
timing problems?
Thanks for any help
Alberto
Attiva Tiscali Voce 8 Mega: telefoni e navighi senza limiti a soli €10 AL MESE
FINO AL 30 GIUGNO 2009. Dopo paghi €29,90 al mese. Attiva entro il 22/01/09!
http://abbonati.tiscali.it/promo/voce8mega/