Re: [Discuss-gnuradio] Firmware is not compatibile

[Przemek Lewandowski]

God demn it, MARCUS !! not Martin sorry for that.

2015-10-15 0:02 GMT+02:00 Przemek Lewandowski <address@hidden>:

Wow Martin you are the best : D

My Board was all the time connected with computer. I didnt realized that it can be a problem. 

Thank You, now its working : )

2015-10-14 23:35 GMT+02:00 Marcus Müller <address@hidden>:

Hello Przemek,

after downloading, you'll have load the firmware onto the device; that usually happens automatically after a power cycle. Did you remove the USRP from power before trying to use it again? I'm asking because I don't see the FPGA loading sequence in your output.

Regarding the version mismatch: that should be ok, UHD 3.10. uses the 3.9 image compatibility.

Best regards,
Marcus

On 14.10.2015 22:28, Przemek Lewandowski wrote:

Hello

My situation is:

I had previously version of GnuRadio from June. Everything worked fine. Today I need to update my software due to patch for multiply_matrix_cc, and I had small problem with Pybomb due to Python Miko that wasnt exist. Ok I installed it. But befor that I searched solution and uninstalled nearly everything. And after that I had installed newest version of GNURadio from repository and newest version of UHD. Now everything is nearly working, buuuut when I want to send my old files to B210 I have this error:

Generating: "/home/przelew/Moje/top_block.py"

Executing: '/usr/bin/python2 -u /home/przelew/Moje/top_block.py'

linux; GNU C++ version 4.8.4; Boost_105400; UHD_003.010.git-38-gc77ffb3e

Traceback (most recent call last):

  File "/home/przelew/Moje/top_block.py", line 260, in <module>

    main()

  File "/home/przelew/Moje/top_block.py", line 248, in main

    tb = top_block_cls()

  File "/home/przelew/Moje/top_block.py", line 75, in __init__

    channels=range(1),

  File "/home/przelew/target/lib/python2.7/dist-packages/gnuradio/uhd/__init__.py", line 122, in constructor_interceptor

    return old_constructor(*args)

  File "/home/przelew/target/lib/python2.7/dist-packages/gnuradio/uhd/uhd_swig.py", line 2034, in make

    return _uhd_swig.usrp_sink_make(*args)

RuntimeError: RuntimeError: Expected firmware compatibility number 8.0, but got 7.0:

The firmware build is not compatible with the host code build.

Please run:

 "/home/przelew/target/lib/uhd/utils/uhd_images_downloader.py"

And yes, I run python script 3 times, and it replaced images properly.... Information should be somewhere else about firmware. OR I have   UHD_003.010  and python scipt downloaded wrong version :) here is the output from python script:

address@hidden:~/target$ python /home/przelew/target/lib/uhd/utils/uhd_images_downloader.py

Images destination:      /home/przelew/target/share/uhd/images

Downloading images from: http://files.ettus.com/binaries/images/uhd-images_003.009.001-release.zip

Downloading images to:   /tmp/tmpq04WZA/uhd-images_003.009.001-release.zip

24703 kB / 24703 kB (100%)

Images successfully installed to: /home/przelew/target/share/uhd/images

Thank You for any advice :)

Przemek Lewandowski

_______________________________________________
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio

_______________________________________________
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio