[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Motorola C350
Andrey V. Panov
Re: Motorola C350
Fri, 12 Mar 2004 15:23:23 +1000
Thanks, I had forgotten to mount usbfs before.
But to my regret gnokii does not support unicode :(
On Tuesday 09 March 2004 07:35, Ron Yorston wrote:
> When I connect my C350 to my Linux system it's using the acm driver
> on port /dev/input/ttyACM0.
> My .gnokiirc file is attached below.
> # This is a sample ~/.gnokiirc file. Copy it into your
> # home directory and name it .gnokiirc.
> # Set port to the physical serial port used to connect to your phone.
> # Linux version is:
> port = /dev/input/ttyACM0
> # For MacOSX you will need something like:
> # port = /dev/cu.USA28X1P1.1
> # Use this setting also for the Bluetooth connection:
> # port = aa:bb:cc:dd:ee:ff
> # Set model to the model number of your phone
> model = AT
> # Initlength controls the number of characters sent to the
> # phone during initialisation. You can either set it to
> # the word "default" or a positive integer.
> # You can try setting this value if you want to connect
> # to the phone quicker. If you've never noticed the
> # connection to be slow, it is suggested that you
> # leave this alone. Read the initialisation code in fbus-xxxx
> # to understand what this changes if you're curious.
> initlength = default
> # The type of the connection, for IR set this to infrared or irda.
> # For the nk6110 driver only infrared is valid for the IrDA connection.
> # See Docs/gnokii-ir-howto for more detailes on this.
> # If you have 6210/6250/7110 phone and dau9p cable (the one you can
> # use with 6100 series and cannot use hardware modem from the phone)
> # you may want to use 'dau9p' value to get faster initialization.
> # If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
> # you don't use model = AT) you may want to use 'dlr3p' value here.
> # Note that it is recommended and currently the best way to use this
> # cable with nk6510 driver.
> connection = serial
> # Set bindir to point to the location of the various gnokii binaries.
> # In particular ensure that mgnokiidev is in this location, with
> # permissions 4750, owned by root, group gnokii. Ensure you
> # are in the gnokii group and that the group exists...
> bindir = /usr/local/sbin
> # Set this to 'yes' if you want gnokii to set and check the lock file in
> # /var/lock directory. It avoids potential conflicts with other serial
> # port software (eg. minicom). If you have wrong permissions for the
> # directory, a warning will be generated. If you don't want a lockfile, set
> # it to 'no'.
> use_locking = yes
> # Baudrate to use on serial port connections.
> # Currently used only by models AT and BIP/CIMD. Defaults to 19200.
> serial_baudrate = 19200
> # Force waiting after each send character the specified usec time.
> # Value -1 forces the fastest 'block' writing,
> # value 0 writes each character separately without any explicite waiting,
> # other positive values specify the appropriate 1/1000000 sec delaying.
> # Siemens M20 requires at least "1"! FIXME: Model-driven autodetection
> #serial_write_usleep = 10000
> # Force serial port handshaking mode, useful primarily for "AT" model.
> # Gnokii "AT" model uses software handshake by default.
> # Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3
> wires) handshake = software
> # If defined (not commented out by '#') it will quit Gnokii anytime
> # when DCD line will drop.
> #require_dcd = 1
> # If you are using a bluetooth connection, you can specify the rfcomm
> # channel number here. Default value is 1.
> #rfcomm_channel = 1
> # Run the specified script(s) right after opening and initializing the
> device # and before any communucation (right before closing for
> disconnect_script). # You may find handy to use it to connect your modem to
> SMS Center # when using BIP or CIMD protocols
> # Non-absolute path is relative to the specific directory where gnokii is
> run! #connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
> #disconnect_script =
> # When sending SMS you can experience timeouts. This is the feature of the
> # overloaded SMSCs. The phones waits for the response from the SMSC
> confirming # that it received the short message. When the SMSC is DoSed
> with many requests # it will take more time to get the response. Adjust it
> to your needs. The # value is given in seconds to wait. Defaults to 10
> seconds. Set to 0 to wait # forever.
> smsc_timeout = 10
> # Any entries in the following two sections will be set as environment
> # variables when running the scripts.
> # Handy for use for $VAR substitutions in your chat(8) script.
> TELEPHONE = 12345678
Andrey V. Panov
panov /@/ canopus.iacp.dvo.ru