pin help

[mikha]

hello.. I'm currently having trouble with PIN on gnokii and 6230

here's what happens during gnokii --identify

GNOKII Version 0.6.12
LOG: debug mask is 0x1
LOG: rlpdebug mask is 0x1
phone instance config:
model: 6230
port_device: 00:0E:ED:E0:5E:DD
connection_type: 5
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device 00:0E:ED:E0:5E:DD
Can't connect: Connection refused
Couldn't open PHONET device: Connection refused
Error in link initialisation: 1
Telephone interface init failed: Command failed.
Quitting.
Serial device: closing device


I'm asked for a pin in my phone
it stops after I enter the pin 1234 on my phone.. and says pairing failed


here's my hcid

#
# HCI daemon configuration file.
#

# HCId options
options {
        # Automatically initialize new devices
        autoinit yes;

        # Security Manager mode
        #   none - Security manager disabled
        #   auto - Use local PIN for incoming connections
        #   user - Always ask user for a PIN
        #
        security auto;

        # Pairing mode
        #   none  - Pairing disabled
        #   multi - Allow pairing with already paired devices
        #   once  - Pair once and deny successive attempts
        pairing multi;

        # PIN helper
        pin_helper /bin/bluepin;

        # D-Bus PIN helper
        #dbus_pin_helper;
}

# Default settings for HCI devices
device {
        # Local device name
        #   %d - device id
        #   %h - host name
        name "%h-%d";

        # Local device class
        class 0x3e0100;

        # Default packet type
        #pkt_type DH1,DM1,HV1;

        # Inquiry and Page scan
        iscan enable; pscan enable;

        # Default link mode
        #   none   - no specific policy 
        #   accept - always accept incoming connections
        #   master - become master on incoming connections,
        #            deny role switch on outgoing connections
        lm accept;

        # Default link policy
        #   none    - no specific policy
        #   rswitch - allow role switch
        #   hold    - allow hold mode
        #   sniff   - allow sniff mode
        #   park    - allow park mode
        lp rswitch,hold,sniff,park;

        # Authentication and Encryption (Security Mode 3)
        #auth enable;
        #encrypt enable;
}

I changed the pin helper variable as I've read about this from a thread.. I
created the/bin/bluepin but still no success..

here's my rfcomm incase needed



#
# RFCOMM configuration file.
#

# example:
#
# rfcomm0 {
  bind yes;
#       # Bluetooth address of the device
        device 00:0E:ED:E0:5E:DD;
#       # RFCOMM channel for the connection
        channel 1;
#       # Description of the connection
        comment "Nokia 6230";
}


and my /bin/bluepin

#!/bin/sh
echo "PIN:1234"


and .gnokiirc



# This is a sample ~/.gnokiirc file.  Copy it into your
# home directory and name it .gnokiirc.
# See http://wiki.gnokii.org/index.php/Config for working examples.
#

[global]

# Set port to the physical port used to connect to your phone.
# Linux version is:
port = 00:0E:ED:E0:5E:DD
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# FreeBSD (probably NetBSD and OpenBSD too) use:
# port = /dev/cuaa0
#
# With Linux-IrDA you will want to use
# port = /dev/ircomm0
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
# when using it with AT driver set it to:
# port = /dev/rfcomm0
# or similiar.
#
# For the Linux USB cables you will need one of the following settings (or
# similiar)
# port = /dev/ttyUSB0
# port = /dev/tts/USB0
# port = /dev/ttyACM0
# the last one will work only with AT driver. The correct setting should be
# given in the dmesg output.

# Set model to the model number of your phone. For the
# Symbian phones use:
# model = series60
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = 6230
# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.

# Set IrDA device name.
# If you use irda connection you may want gnokii to autodetect the irda
# device it connects to. This is fine for most of the cases. if you have
# more than one device in range you may want to give manually the device
# name so gnokii correctly recognizes it. Use the name that you can see
# in the discovery log when the phone with infrared is in the range of
# your irda port.
# Note that you need to set this for each phone_ section separately. It
# isn't nested from the global section.
# irda_string = Nokia 6610i

# Initlength controls the number of characters sent to the
# phone during initialisation.  You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker.  If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone.  Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default

# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
# connection = bluetooth
# With DKU-2 cable use the following setting if you want to libusb driver
# (recommended):
# connection = dku2libusb
# or the following setting if you want to use Linux kernel driver
# connection = dku2
# With DKU-5 cable use the following setting
# connection = dku5
# For Bluetooth and AT driver use the following setting
# connection = serial
# For other Bluetooth settings use
connection = bluetooth
# For infrared connection with phones other than Nokia 6110/6130/6150 use
# connection = irda


# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes

# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200

# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"!  FIXME: Model-driven autodetection
#serial_write_usleep = 10000

# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3
wires)
#handshake = software

# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1

# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
rfcomm_channel = 1

# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1

# Run the specified script(s) right after opening and initializing the
device
# and before any communication (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is
run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =

# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC
confirming
# that it received the short message. When the SMSC is DoSed with many
requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to
wait
# forever.
smsc_timeout = 10

# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii.  Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/local/sbin/

# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
[connect_script]
TELEPHONE = 12345678
[disconnect_script]


# The following parameters control how libgnokii handle the debugging
messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.

[logging]

# where to log the debug output (on: stderr, off: /dev/null)
debug = on

# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = on

# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off

hoping for your help.. thank you
-- 
View this message in context: 
http://www.nabble.com/pin-help-tf3186650.html#a8844393
Sent from the gnokii-users mailing list archive at Nabble.com.