[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: gnokii configuration for Nokia 6230i on Ubuntu 16.04

From: rverzola
Subject: Re: gnokii configuration for Nokia 6230i on Ubuntu 16.04
Date: Fri, 7 Sep 2018 23:55:26 +0100 (BST)
User-agent: SquirrelMail/1.4.10 [CVS]

This is my config file for 6220 and it worked.The 6220 is gone now
unfortunately. I used bluetooth. I'm not sure if it will also work with
6230. Try to make it work with bluetooth first. If you manage to do it,
try USB next.


# This is a sample ~/.gnokiirc file.  Copy it into your
# home directory and name it .gnokiirc.
# See for working examples.
# Configuration for Globe SIM


# Set port to the physical port used to connect to your phone.
# Linux version is:
#port = /dev/ttyS1
#port = /dev/ttyS0
port = 00:22:fc:63:22:ab

# Set model to the model number of your phone. For the
# Symbian phones use:
# model = AT

# For other non-Nokia phones and when you want to use AT
# mode use:
model = AT

# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
# model = series40
# model = series60

# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.

# Initlength controls the number of characters sent to the
# phone during initialisation.  You can either set it to
# the word "default" or a positive integer.
# You can try setting this value if you want to connect
# to the phone quicker.  If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone.  Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default

# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
#connection = dlr3p
connection = bluetooth

# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes

# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200

# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"!  FIXME: Model-driven autodetection
#serial_write_usleep = 10000

# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3
#handshake = software

# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1

# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1

# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1

# Run the specified script(s) right after opening and initializing the device
# and before any communication (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =

# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC
# that it received the short message. When the SMSC is DoSed with many
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10

# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii.  Ensure you
# are in the gnokii group and that the group exists...
bindir = /usr/local/sbin/

# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
TELEPHONE = 09213131717

# The following parameters control how libgnokii handle the debugging
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.


# where to log the debug output (on: stderr, off: /dev/null)
debug = off

# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = off

# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off

> On Thu, Sep 06, 2018 at 10:35:19AM +0100, Dan Lindfield wrote:
>> Struggling to get *gnokii* to interface with my Nokia 6230i through USB
>> Nokia cable. Got past the serial device "Permission Denied" by changing
>> permissions "sudo chmod 777 /dev/ttyACM0" but then get either "Device or
>> resource busy" or "Initialization failed (6) - Telephone interface init
>> failed: Function or connection type not supported by the phone or by the
>> phone driver". Can anyone help understand what is missing? Is it an
>> issue
>> with the cdc-acm driver and compatibility with phonet on my particular
>> Ubuntu build?
> -EBUSY suggests something else might keep ttyACM0 opened. ModemManager for
> example? I'd suggest you use lsof utility to verify that.
> Best regards,
>       ladis
> _______________________________________________
> gnokii-users mailing list
> address@hidden

reply via email to

[Prev in Thread] Current Thread [Next in Thread]