[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Gluglug X200 hangs on boot after `# guix system reconfigure /etc/sysconf

From: 白い熊
Subject: Gluglug X200 hangs on boot after `# guix system reconfigure /etc/sysconfig.scm', right after starting dmd
Date: Mon, 09 Mar 2015 11:46:11 +0100
User-agent: K-9 Mail for Android

I've installed GuixSD on the Gluglug X200 without a problem, using instructions 
for the X60. [1]

Did `# guix pull' and reconfigured the system to enable the wicd service. [2]

However on the Gluglug X200 the system freezes upon reboot with a kernel panic 
if “(wicd-service)” is included in services in sysconfig.scm, same symptoms 
upon boot crash as another user has experienced with the X200. [3]

The current kernel is 3.18.9.

If sysconfig.scm contains: 

(use modules (gnu))
(use-service-modules xorg networking dbus avahi)
(use-package-modules avahi wicd)
(services (cons* (slim-service)
                 (dbus-service (list wicd))

the system boots no problem after reconfigure. However wicd can't be started 
even with the dbus-enable hack [4], as the “wicd-service” is logically not 
present, and thus “sudo deco enable wicd” fails with “No service at all 
providing wicd.”

Now when just “(wicd-service)” is added to services, this being the only change 
compared with the above, the system will hang on boot.

There are no error messages on boot up to dmd start. Then it fails with:

setting up setuid programs in '/run/setuid-programs'...
making '/gnu/store/h5s1apxpmg8cgdwj9x3yzyxj8f6zizzr-system' the current 
[    2.915986] random: nonblocking pool is initialized
Service dmd has been started.
Assertion (null? (lookup-services (canonical-name new))) failed.
[    4.706625] Kernel panic - not syncing: Attempted to kill init! 
[    4.706625]
[    4.708661] CPU: 1 PID: 1 Comm: dmd Tainted: G         I    3.18.9-gnu #1
[    4.709216] Hardware name: LENOVO 7459ED2/7459ED2, BIOS CBET4000 4.0 
[    4.709216]  ffff88023310f100 ffff880234097e28 ffffffff8175e8cb 
[    4.709216]  ffffffff81a7aad0 ffff880234097ea8 ffffffff817599be 
[    4.709216]  ffffffff00000010 ffff880234097eb8 ffff880234097e58 
[    4.709216] Call Trace:
[    4.709216]  [<ffffffff8175e8cb>] dump_stack+0x46/0x58
[    4.709216]  [<ffffffff817599be>] panic+0xc1/0x1f5
[    4.709216]  [<ffffffff81074507>] do_exit+0xa67/0xa70
[    4.709216]  [<ffffffff8109cee0>] ? wake_up_state+0x10/0x20
[    4.709216]  [<ffffffff8107de52>] ? signal_wake_up_state+0x22/0x40
[    4.709216]  [<ffffffff8107459f>] do_group_exit+0x3f/0xa0
[    4.709216]  [<ffffffff81074614>] SyS_exit_group+0x14/0x20
[    4.709216]  [<ffffffff81766c6d>] system_call_fastpath+0x16/0x1b
[    4.709216] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 
[    4.709216] ---[ end Kernel panic - not syncing: Attempted to kill init! 
[    4.709216]

I'll be much obliged for help in getting wicd working on the Gluglug X200. 

Best regards, 
白い熊 @相撲道


reply via email to

[Prev in Thread] Current Thread [Next in Thread]