[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Original config from a documentation causes an error with keyboard-l

From: Adam Mazurkiewicz
Subject: Re: Original config from a documentation causes an error with keyboard-layout function
Date: Wed, 8 May 2019 10:02:22 +0200

I processed the installation try from usb flash stick. First I formatted a
target partition for the new Guixsd instance with ext4 and labeled it
guixsd. Then I did that follows and put 'guix describe':

address@hidden ~# ifconfig enp2s0 up && \
> dhclient enp2s0 -v
[  173.423231] RTL8211B Gigabit Ethernet r8169-200:00: attached PHY driver
[RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
[  173.524320] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
enp2s0    Link encap:Ethernet  HWaddr 00:23:54:60:DA:20
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[  173.525924] r8169 0000:02:00.0 enp2s0: Link is Down
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0  TX bytes:0

Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit

Listening on LPF/enp2s0/00:23:54:60:da:20
Sending on   LPF/enp2s0/00:23:54:60:da:20
Sending on   Socket/fallback
DHCPDISCOVER on enp2s0 to port 67 interval 6
[  175.062429] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full - flow
control off
[  175.062723] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
DHCPDISCOVER on enp2s0 to port 67 interval 12
DHCPREQUEST for on enp2s0 to port 67
DHCPACK of from
bound to -- renewal in 266 seconds.
address@hidden ~# mount /dev/disk/by-label/guixsd /mnt && \
> mkdir /mnt/etc
[  240.335408] EXT4-fs (sda1): recovery complete
[  240.337345] EXT4-fs (sda1): mounted filesystem with ordered data mode.
Opts: (null)
address@hidden ~# cp /root/sda6/home/s/Dropbox/Guix/scm1/config.scm /mnt/etc/
address@hidden ~# herd start cow-store /mnt
Service cow-store has been started.
address@hidden ~# guix system init /mnt/etc/config.scm /mnt/
/mnt/etc/config.scm:5:0: error: extraneous field initializers
address@hidden ~# guix describe
guix describe: error: failed to determine origin
address@hidden ~#

śr., 8 maj 2019 o 08:46 swedebugia <address@hidden> napisał(a):

> On 2019-05-08 07:00, Adam Mazurkiewicz wrote:
> ...
> >
> > Using this file caused the error:
> > /root/sda6/home/s/Dropbox/Guix/scm1/config.scm:5:0: error: extraneous
> field
> > initializers (keyboard-layout)
> >
> > So it is something wrong with the keyboard-layout function. The function
> is
> > used a few times so we do not know which one actually causes the error.
> >
> > Is this the documentation mistake or I am doing something wrong? How to
> use
> > the function keyboard-layout properly?
> >
> Could you add the output of "guix describe"?
> How did you install guix?
> --
> Cheers
> Swedebugia

reply via email to

[Prev in Thread] Current Thread [Next in Thread]