paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] Tiny v2.11 - Programming help required


From: Ben Paratz
Subject: Re: [Paparazzi-devel] Tiny v2.11 - Programming help required
Date: Sat, 6 Sep 2008 08:12:22 -0400

Just one more thing, I powered up the Tiny for about a minute, and a few components on the GPS antenna side of the board got too hot to touch. Is this normal? I am powering the board with a 2-Cell 7.4v Li-Po connected to the "+ and -" battery input in the centre of the board. Plugged in are two servos, IR sensors, and a serial cable which is connected to the airborne modem. I am powering the airborne modem with +5VDC from the Tiny, and I have also connected the +5VDC to the shutdown pin as per the wiki.

"I have same problem of using wireless link, but what I do suggest is that can
you confrim your autopilot has no problem by connecting to your wire to laptop
(FTDI cable, the one you use for bootloader).

 If you have done that, and find when your autopilot has no problem, then you
are in the same stage as me (which mean I am still try to configure my Xbee
modem)."

I would like to do that, but don't have an FTDI cable. The maxstream modem plugs straight into the usb port, so i guess it is built into it. I bought my Tiny off PPZUAV so didn't have to do the bootloader myself.

Does the aircraft have to be powered up for the GCS to load? I haven't seen any instructions about how to actually start the GCS.

Thanks,
Ben

On Sat, Sep 6, 2008 at 7:44 AM, Ben Paratz <address@hidden> wrote:
Hi Guys,
 
Thanks very much for all your help, I've had much more success thanks to it.
I spent all of today playing with paparazzi, and this is what I have:
- The airframe file is successfully compiling, and has been uploaded to the autopilot. I had to create another airframe file, as the one I posted first caused the autopilot to do nothing. I found out that this is likely because the program was for an earlier version of the Tiny. I have based the new aiframe file on funjet1.xml
- The servos (through the autopilot) respond correctly to my JR transmitter. I used a JR R700, but modified it as per the link earlier in the thread.

The flight plan I have uploaded is "Muret demo"

The only thing now is that the GCS is not populating. It loaded fully once, after I ran a simulation, but I cannot get it to do it again. When I execute a session the GCS window pops up, but remains blank... I have tried using both "Flight address@hidden" and "Flight address@hidden" but neither seems to help the GCS load. I think the defult baud rate for the Maxstream modem is 9600

When I plug in the modem this what I get:

tail -f /var/log/messages
Sep  5 09:14:16 ben-laptop kernel: [ 1461.018531] usb 1-1: new full speed USB device using uhci_hcd and address 4
Sep  5 09:14:16 ben-laptop kernel: [ 1461.040458] usb 1-1: configuration #1 chosen from 1 choice
Sep  5 09:14:16 ben-laptop kernel: [ 1461.046091] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
Sep  5 09:14:16 ben-laptop kernel: [ 1461.046149] /build/buildd/linux-2.6.24/drivers/usb/serial/ftdi_sio.c: Detected FT232BM
Sep  5 09:14:16 ben-laptop kernel: [ 1461.046277] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0

Do you have any ideas how to get the GCS to load? I have attached the new airframe code below. Let me know if you need me to post any more files.

Thanks,
Ben


<!DOCTYPE airframe SYSTEM "airframe.dtd">

<!-- Funjet Multiplex (http://www.multiplex-rc.de/)
     Tiny 2.1 board (http://paparazzi.enac.fr/wiki/index.php/Tiny_v2)
     Tilted infrared sensor (http://paparazzi.enac.fr/wiki/index.php/Image:Tiny_v2_1_Funjet.jpg)
     Radiotronix modem
-->

<airframe name="Easystar Tiny 2.1">

<!-- commands section -->
  <servos>
    <servo name="THROTTLE" no="2" min="1000" neutral="1500" max="2000"/>
    <servo name="ROLL"  no="3" min="1000" neutral="1500" max="2000"/>
    <servo name="PITCH" no="4" min="1000" neutral="1500" max="2000"/>

  </servos>

  <commands>
    <axis name="THROTTLE" failsafe_value="0"/>
    <axis name="ROLL"     failsafe_value="0"/>

    <axis name="PITCH"    failsafe_value="0"/>
  </commands>

  <rc_commands>
    <set command="THROTTLE" value="@THROTTLE"/>
    <set command="ROLL"     value="@ROLL"/>
    <set command="PITCH"    value="@PITCH"/>
  </rc_commands>

  <command_laws>
    <set servo="THROTTLE" value="@THROTTLE"/>
    <set servo="ROLL"  value="@ROLL"/>
    <set servo="PITCH" value="@PITCH"/>

  </command_laws>

  <section name="AUTO1" prefix="AUTO1_">
    <define name="MAX_ROLL" value="0.3"/>
    <define name="MAX_PITCH" value="0.3"/>

  </section>

  <section name="adc" prefix="ADC_CHANNEL_">
    <define name="IR1" value="ADC_1"/>
    <define name="IR2" value="ADC_2"/>
    <define name="IR_TOP" value="ADC_0"/>
    <define name="IR_NB_SAMPLES" value="16"/>

  </section>

  <section name="INFRARED" prefix="IR_">
    <define name="ADC_IR1_NEUTRAL" value="512"/>
    <define name="ADC_IR2_NEUTRAL" value="512"/>
    <define name="ADC_TOP_NEUTRAL" value="512"/>

    <define name="LATERAL_CORRECTION" value="1."/>
    <define name="LONGITUDINAL_CORRECTION" value="1."/>
    <define name="VERTICAL_CORRECTION" value="1.5"/>


    <define name="HORIZ_SENSOR_TILTED" value="1"/>
    <define name="IR2_SIGN" value="-1"/>
    <define name="TOP_SIGN" value="-1"/>

    <define name="ROLL_NEUTRAL_DEFAULT" value="0" unit="deg"/>
    <define name="PITCH_NEUTRAL_DEFAULT" value="0" unit="deg"/>

    <define name="CORRECTION_UP" value="1."/>
    <define name="CORRECTION_DOWN" value="1."/>
    <define name="CORRECTION_LEFT" value="1."/>
    <define name="CORRECTION_RIGHT" value="1."/>
  </section>

  <section name="BAT">
    <define name="MILLIAMP_PER_PERCENT" value="0.86"/>

    <define name="CATASTROPHIC_BAT_LEVEL" value="5.5" unit="V"/>
  </section>
 
  <section name="MISC">
    <define name="NOMINAL_AIRSPEED" value="7" unit="m/s"/>
    <define name="CARROT" value="5." unit="s"/>
    <define name="KILL_MODE_DISTANCE" value="(1.5*MAX_DIST_FROM_HOME)"/>
    <define name="CONTROL_RATE" value="60" unit="Hz"/>
<!--    <define name="XBEE_INIT" value="\"ATPL2\rATRN1\rATTT80\r\""/> -->
<!--    <define name="NO_XBEE_API_INIT" value="TRUE"/> -->
    <define name="ALT_KALMAN_ENABLED" value="TRUE"/>

    <define name="TRIGGER_DELAY" value="1."/>
    <define name="DEFAULT_CIRCLE_RADIUS" value="80."/>
    <define name="MIN_CIRCLE_RADIUS" value="35."/>

  </section>
 
  <section name="VERTICAL CONTROL" prefix="V_CTL_">

    <define name="POWER_CTL_BAT_NOMINAL" value="7.2" unit="volt"/>
    <!-- outer loop proportional gain -->
    <define name="ALTITUDE_PGAIN" value="-0.04"/>

    <!-- outer loop saturation -->
    <define name="ALTITUDE_MAX_CLIMB" value="2."/>

    <!-- auto throttle inner loop -->
    <define name="AUTO_THROTTLE_NOMINAL_CRUISE_THROTTLE" value="0.35"/>
    <define name="AUTO_THROTTLE_MIN_CRUISE_THROTTLE" value="0.3"/>

    <define name="AUTO_THROTTLE_MAX_CRUISE_THROTTLE" value="0.80"/>
    <define name="AUTO_THROTTLE_LOITER_TRIM" value="1500"/>
    <define name="AUTO_THROTTLE_DASH_TRIM" value="-1000"/>
    <define name="AUTO_THROTTLE_CLIMB_THROTTLE_INCREMENT" value="0.1" unit="%/(m/s)"/>
    <define name="AUTO_THROTTLE_PGAIN" value="-0.02"/>

    <define name="AUTO_THROTTLE_IGAIN" value="0.1"/>
    <define name="AUTO_THROTTLE_PITCH_OF_VZ_PGAIN" value="0.1"/>


    <!-- auto pitch inner loop -->
    <define name="AUTO_PITCH_PGAIN" value="-0.05"/>
    <define name="AUTO_PITCH_IGAIN" value="0.075"/>
    <define name="AUTO_PITCH_MAX_PITCH" value="0.35"/>
    <define name="AUTO_PITCH_MIN_PITCH" value="-0.35"/>

   <define name="THROTTLE_SLEW" value="2.0"/>


  </section>

  <section name="HORIZONTAL CONTROL" prefix="H_CTL_">
    <define name="COURSE_PGAIN" value="-1.2"/>

    <define name="ROLL_MAX_SETPOINT" value="0.7" unit="radians"/>

    <define name="PITCH_MAX_SETPOINT" value="0.5" unit="radians"/>
    <define name="PITCH_MIN_SETPOINT" value="-0.5" unit="radians"/>

    <define name="PITCH_PGAIN" value="-10000."/>
    <define name="PITCH_DGAIN" value="1.5"/>

    <define name="ELEVATOR_OF_ROLL" value="0"/>

    <define name="ROLL_ATTITUDE_GAIN" value="-7500"/>
    <define name="ROLL_RATE_GAIN" value="-1500"/>
  </section>

  <section name="NAV">
    <define name="NAV_PITCH" value="0."/>
    <define name="NAV_GLIDE_PITCH_TRIM" value="0.1"/>

  </section>

  <section name="AGGRESSIVE" prefix="AGR_">
    <define name="BLEND_START" value="20"/><!-- Altitude Error to Initiate Aggressive Climb CANNOT BE ZERO!!-->
    <define name="BLEND_END" value="10"/><!-- Altitude Error to Blend Aggressive to Regular Climb Modes  CANNOT BE ZERO!!-->
    <define name="CLIMB_THROTTLE" value="1.0"/><!-- Gaz for Aggressive Climb -->
    <define name="CLIMB_PITCH" value="0.25"/><!-- Pitch for Aggressive Climb -->
    <define name="DESCENT_THROTTLE" value="0.1"/><!-- Gaz for Aggressive Decent -->
    <define name="DESCENT_PITCH" value="-0.15"/><!-- Pitch for Aggressive Decent -->

    <define name="CLIMB_NAV_RATIO" value="0.8"/><!-- Percent Navigation for Altitude Error Equal to Start Altitude -->
    <define name="DESCENT_NAV_RATIO" value="1.0"/>
    </section>

  <section name="FAILSAFE" prefix="FAILSAFE_">
    <define name="DELAY_WITHOUT_GPS" value="2" unit="s"/>
        <define name="DEFAULT_THROTTLE" value="0.0" unit="%"/>

        <define name="DEFAULT_ROLL" value="0.3" unit="rad"/>
        <define name="DEFAULT_PITCH" value="0.3" unit="rad"/>

    <define name="HOME_RADIUS" value="100" unit="m"/>
</section>
 
<!--
 <section name="DATALINK" prefix="DATALINK_">
    <define name="DEVICE_TYPE" value="XBEE"/>

    <define name="DEVICE_ADDRESS" value="...."/>
  </section>
-->

 <section name="SIMU">
    <define name="YAW_RESPONSE_FACTOR" value="0.5"/>
 </section>

 <makefile>
CONFIG = \"tiny_2_1.h\"


include $(PAPARAZZI_SRC)/conf/autopilot/tiny.makefile

FLASH_MODE=IAP

ap.CFLAGS +=  -DFBW -DAP -DCONFIG=$(CONFIG) -DLED -DTIME_LED=1

ap.srcs = sys_time.c $(SRC_ARCH)/sys_time_hw.c $(SRC_ARCH)/armVIC.c main_fbw.c main_ap.c main.c

ap.srcs += commands.c

ap.CFLAGS += -DACTUATORS=\"servos_4017_hw.h\" -DSERVOS_4017
ap.srcs += $(SRC_ARCH)/servos_4017_hw.c actuators.c


ap.CFLAGS += -DRADIO_CONTROL -DRADIO_CONTROL_TYPE=RC_JR
ap.srcs += radio_control.c $(SRC_ARCH)/ppm_hw.c 

#XBEE ap.CFLAGS += -DDOWNLINK -DUSE_UART1 -DDOWNLINK_TRANSPORT=XBeeTransport -DXBEE_UART=Uart1 -DDATALINK=XBEE -DUART1_BAUD=B9600
#XBEE ap.srcs += downlink.c $(SRC_ARCH)/uart_hw.c datalink.c xbee.c

#TRANSPARENT
ap.CFLAGS += -DDOWNLINK -DUSE_UART1 -DDOWNLINK_TRANSPORT=PprzTransport -DDOWNLINK_FBW_DEVICE=Uart1 -DDOWNLINK_AP_DEVICE=Uart1 -DPPRZ_UART=Uart1 -DDATALINK=PPRZ -DUART1_BAUD=B9600

ap.srcs += downlink.c $(SRC_ARCH)/uart_hw.c datalink.c pprz_transport.c


ap.CFLAGS += -DINTER_MCU
ap.srcs += inter_mcu.c

ap.CFLAGS += -DADC -DUSE_ADC_0 -DUSE_ADC_1 -DUSE_ADC_2 -DUSE_ADC_3

ap.srcs += $(SRC_ARCH)/adc_hw.c

ap.CFLAGS += -DGPS -DUBX -DUSE_UART0 -DGPS_LINK=Uart0 -DUART0_BAUD=B38400
# -DGPS_LED=2
ap.srcs += gps_ubx.c gps.c latlong.c

ap.CFLAGS += -DINFRARED -DALT_KALMAN

ap.srcs += infrared.c estimator.c

ap.CFLAGS += -DNAV -DAGR_CLIMB -DLOITER_TRIM

ap.srcs += nav.c fw_h_ctl.c fw_v_ctl.c

# Config for SITL simulation
include $(PAPARAZZI_SRC)/conf/autopilot/sitl.makefile
sim.CFLAGS += -DCONFIG=\"tiny.h\" -DAGR_CLIMB -DLOITER_TRIM -DALT_KALMAN

# a test program to setup actuators
setup_actuators.ARCHDIR = $(ARCHI)
setup_actuators.ARCH = arm7tdmi
setup_actuators.TARGET = setup_actuators
setup_actuators.TARGETDIR = setup_actuators

setup_actuators.CFLAGS += -DFBW -DCONFIG=\"tiny.h\" -DLED -DTIME_LED=1 -DACTUATORS=\"servos_4015_hw.h\" -DSERVOS_4015 -DUSE_UART1 -DUART1_BAUD=B9600 -DDATALINK=PPRZ -DPPRZ_UART=Uart1
setup_actuators.srcs += sys_time.c $(SRC_ARCH)/sys_time_hw.c $(SRC_ARCH)/armVIC.c pprz_transport.c setup_actuators.c $(SRC_ARCH)/uart_hw.c $(SRC_ARCH)/servos_4015_hw.c main.c

  </makefile>
</airframe>

On Sat, Sep 6, 2008 at 7:47 PM, David Buzz Carlson <address@hidden> wrote:
Looking through his airframe file, it seems he is using ADC_6 for his vertical IR sensor.  However, http://paparazzi.enac.fr/wiki/index.php/Tiny_v2  would have me believe that IRV is ADC_0.  I believe ADC_0 is the correct one, can anybody confirm that for me?

Buzz

address@hidden wrote:
Ben

I believe the maxstream packages use an FTDI USB-to-serial converter chip (everything in linux is chip-specific).  The FTDI driver is already present and functional in Ubuntu so you may be all set.  Type "dmesg | tail" after plugging in the modem and look for something about ftdi on ttyusb0 or such.  
The ground modem can be any baud you want.  Maxtream and some others allow independent configuration of the RF baud and serial port baud to allow the air and ground serial baud rates to be unequal so long as the RF rates are equal.  Make sure your ap and airborne modem are at the same baud (-DUART0_BAUD=B9600 in your case) and same for the gcs (link line should have "-s 9600" or such to match the ground modem) and make sure your modems are each configured for their appropriate baud rates as well (maybe 9600 is the default?).

The RC modes are set in conf/radios/*.xml but I don't know how those settings get mapped to channels 1 thru 8.  I usually use the transmitter programming to change the channel of my switch until I find the one that works.

Your airframe file looks ok but I should point out that the GPS failsafe values on many of the cvs airframes are strange, specifying 30% throttle, 30 degree pitch up, and 17 degree roll in the event of a total loss of GPS position info.  It sounds to me more like a wild spin, throttle-on crash and lipo fire.  I advise something more like 0 throttle, 10 deg up and 17 roll or whatever produces a gentle circling glide on your airframe.  I think these pitch/roll values are used in "kill" mode as well so you can test them in the air.
____________________________________________________________
Fashion Design Education - Click Here!
http://thirdpartyoffers.juno.com/TGL2141/fc/Ioyw6i3oIaxayhf6v0qyKFdfvXplzTMUHQ82EF1TvuOwIQPzEsrgkl/

------------------------------------------------------------------------


Hi,

I have a Tiny v2.11 autopilot with all the hardware needed for autonomous flight. I have started on the programming, but have run into a few difficulties.

I have installed all the hardware in my aircraft, but have not gotten any further than that succesfully. I am meant to be demonstrating autonomous flight a week from now, so it would be really great if I could get the autopilot fully working by then.

I am new to Linux, and have run into some problems regarding the programming. It would be extremely helpful if you could provide some assistance. I am using Ubuntu 8.04.1 - Hardy Heron

I have been studying the Wiki and following it very closely.

This is what I need help with:

- Installing the drivers for the radio modem (the ground-station modem. It plugs into the USB port and grabs the serial signals. I'm sure you know all about this... The readme file that came with it says that I need to compile the driver into a 'Loadable Kernel Module' but I am unsure how to do this. The modem I am using is a Digi (Maxstream) 9XTend operating on 900MHz. I have been told that I may not need to install the driver, but can you please advise me on what to do.

- Configuring the rc radio settings: I am using a 6-channel JR Radio. I have found (using a scope) that my JR R700 7-channel receiver outputs the ppm signal through the 'signal' pin in the battery connector. I can attach a picture of the signal if you want. Also, how do you choose which channel determines the mode? (Auto 1, Auto 2, Manual).

- Configuring the airframe file: I have had a go at making my own airframe file (following the wiki), but are not sure if it is correct. I have pasted the code at the bottom. My airframe is very simple: A 3-Channel Easystar. It also hope to be able to trigger a servo for controlling the shutter on a camera at a set position, but I will keep it simple and focus on achieving autonomous flight first.


It would really be great if you could help me get this working within the next week.

Thankyou very much,

Ben


Here is my airframe code:

<!DOCTYPE airframe SYSTEM "airframe.dtd">

<airframe name="EASYSTAR">
 <!-- tiny v2.11 airframe -->

<!-- commands section -->
 <servos>
   <servo name="THROTTLE"  no="0" min="1000" neutral="1500" max="2000"/>
   <servo name="RUDDER"  no="2" min="1000" neutral="1500" max="2000"/>
   <servo name="ELEVATOR" no="6" min="1000" neutral="1500" min="2000"/>
 </servos>

 <commands>
   <axis name="THROTTLE" failsafe_value="0"/>
   <axis name="YAW"     failsafe_value="0"/>
   <axis name="PITCH"    failsafe_value="0"/>
 </commands>

 <rc_commands>
   <set command="THROTTLE" value="@THROTTLE"/>
   <set command="ROLL"     value="@ROLL"/>
   <set command="PITCH"    value="@PITCH"/>
 </rc_commands>

 <command_laws>
   <set servo="THROTTLE" value="@THROTTLE"/>
   <set servo="RUDDER" value="@ROLL"/>
<set servo="ELEVATOR" value="@PITCH"/>
 </command_laws>

 <section name="AUTO1" prefix="AUTO1_">
   <define name="MAX_ROLL" value="0.6"/>
   <define name="MAX_PITCH" value="0.6"/>
 </section>

 <section name="adc" prefix="ADC_CHANNEL_">
   <define name="IR1" value="ADC_0"/>
   <define name="IR2" value="ADC_1"/>
   <define name="IR_TOP" value="ADC_6"/>

 </section>

 <section name="INFRARED" prefix="IR_">
   <define name="ADC_IR1_NEUTRAL" value="512"/>
   <define name="ADC_IR2_NEUTRAL" value="512"/>
   <define name="ADC_TOP_NEUTRAL" value="512"/>
   <define name="IR2_SIGN" value="-1"/>
   <define name="TOP_SIGN" value="-1"/>
   <define name="HORIZ_SENSOR_TILTED" value="1"/>
   <define name="LATERAL_CORRECTION" value="1"/>
   <define name="LONGITUDINAL_CORRECTION" value="1"/>
   <define name="VERTICAL_CORRECTION" value="1"/>
   <define name="ROLL_NEUTRAL_DEFAULT" value="0" unit="deg"/>
   <define name="PITCH_NEUTRAL_DEFAULT" value="0" unit="deg"/>
   <define name="CORRECTION_UP" value="1"/>
   <define name="CORRECTION_DOWN" value="1"/>
   <define name="CORRECTION_LEFT" value="1"/>
   <define name="CORRECTION_RIGHT" value="1"/>

 </section>

 <section name="BAT">
   <define name="MILLIAMP_PER_PERCENT" value="0.86"/>
   <define name="CATASTROPHIC_BAT_LEVEL" value="5.5" unit="V"/>
 </section>
   <section name="MISC">
   <define name="NOMINAL_AIRSPEED" value="7" unit="m/s"/>
   <define name="CARROT" value="5." unit="s"/>
   <define name="KILL_MODE_DISTANCE" value="(1.5*MAX_DIST_FROM_HOME)"/>
   <define name="CONTROL_RATE" value="60" unit="Hz"/>
 </section>
   <section name="PID">
   <define name="ROLL_PGAIN" value="5000."/>
   <define name="PITCH_OF_ROLL" value="0.25"/>
   <define name="PITCH_PGAIN" value="10000."/>
   <define name="MAX_ROLL" value="0.35"/>
   <define name="MAX_PITCH" value="0.35"/>
   <define name="MIN_PITCH" value="-0.35"/>
   <define name="AILERON_OF_THROTTLE" value="0.0"/>
   <define name="CRUISE_THROTTLE" value="0.35"/>
 </section>
   <section name="ALT" prefix="CLIMB_">
   <define name="PITCH_PGAIN" value="-0.05"/>
   <define name="PITCH_IGAIN" value="0.075"/>
   <define name="PGAIN" value="-0.01"/>
   <define name="IGAIN" value="0.1"/>
   <define name="MAX" value="1."/>
   <define name="PITCH_OF_VZ_PGAIN" value="0.05"/>
   <define name="THROTTLE_OF_CLIMB" value="0.15" unit="%/(m/s)"/>
 </section>
   <section name="HORIZONTAL CONTROL" prefix="H_CTL_">
   <define name="COURSE_PGAIN" value="-0.4"/>
   <define name="ROLL_MAX_SETPOINT" value="0.6" unit="radians"/>
   <define name="PITCH_MAX_SETPOINT" value="0.5" unit="radians"/>
   <define name="PITCH_MIN_SETPOINT" value="-0.5" unit="radians"/>


   <define name="ROLL_PGAIN" value="5000."/>
   <define name="AILERON_OF_THROTTLE" value="0.0"/>
   <define name="PITCH_PGAIN" value="-9000."/>
   <define name="PITCH_DGAIN" value="1.5"/>
     <!--  roll rate loop -->
   <define name="ROLL_RATE_MODE_DEFAULT" value="1"/>
   <define name="ROLL_RATE_SETPOINT_PGAIN" value="-5." unit="rad/s/rad"/>
   <define name="ROLL_RATE_MAX_SETPOINT" value="10"/>
   <define name="LO_THROTTLE_ROLL_RATE_PGAIN" value="1000."/>
   <define name="HI_THROTTLE_ROLL_RATE_PGAIN" value="1000."/>
   <define name="ROLL_RATE_IGAIN" value="0"/>
   <define name="ROLL_RATE_DGAIN" value="0"/>
   <define name="ROLL_RATE_SUM_NB_SAMPLES" value="64"/>

 </section>

 <section name="VERTICAL CONTROL" prefix="V_CTL_">

   <define name="POWER_CTL_BAT_NOMINAL" value="6" unit="volt"/>
   <!-- outer loop proportional gain -->
   <define name="ALTITUDE_PGAIN" value="-0.03"/>
   <!-- outer loop saturation -->
   <define name="ALTITUDE_MAX_CLIMB" value="2."/>

   <!-- auto throttle inner loop -->
   <define name="AUTO_THROTTLE_NOMINAL_CRUISE_THROTTLE" value="0.4"/>
   <define name="AUTO_THROTTLE_MIN_CRUISE_THROTTLE" value="0.30"/>
   <define name="AUTO_THROTTLE_MAX_CRUISE_THROTTLE" value="0.80"/>
   <define name="AUTO_THROTTLE_LOITER_TRIM" value="1500"/>
   <define name="AUTO_THROTTLE_DASH_TRIM" value="-1000"/>
   <define name="AUTO_THROTTLE_CLIMB_THROTTLE_INCREMENT" value="0.15" unit="%/(m/s)"/>
   <define name="AUTO_THROTTLE_PGAIN" value="-0.01"/>
   <define name="AUTO_THROTTLE_IGAIN" value="0.1"/>
   <define name="AUTO_THROTTLE_PITCH_OF_VZ_PGAIN" value="0.05"/>

   <!-- auto pitch inner loop -->
   <define name="AUTO_PITCH_PGAIN" value="-0.05"/>
   <define name="AUTO_PITCH_IGAIN" value="0.075"/>
   <define name="AUTO_PITCH_MAX_PITCH" value="0.35"/>
   <define name="AUTO_PITCH_MIN_PITCH" value="-0.35"/>

  <define name="THROTTLE_SLEW" value="0.1"/>

 </section>


 <section name="NAV">
   <define name="NAV_PITCH" value="0.0"/>
   <define name="NAV_GLIDE_PITCH_TRIM" value="0.2"/>
   <define name="DEFAULT_CIRCLE_RADIUS" value="100" unit="m"/>
 </section>

 <section name="AGGRESSIVE" prefix="AGR_">
   <define name="CLIMB_THROTTLE" value="0.95"/><!-- Throttle for Aggressive Climb -->
   <define name="DESCENT_THROTTLE" value="0.1"/><!-- Throttle for Aggressive Decent -->
   <define name="CLIMB_PITCH" value="0.3"/><!-- Pitch for Aggressive Climb -->
   <define name="DESCENT_PITCH" value="-0.25"/><!-- Pitch for Aggressive Decent -->
   <define name="BLEND_START" value="20"/><!-- Altitude Error to Initiate Aggressive Climb CANNOT BE ZERO!!-->
   <define name="BLEND_END" value="10"/><!-- Altitude Error to Blend Aggressive to Regular Climb Modes  CANNOT BE ZERO!!-->
   <define name="CLIMB_NAV_RATIO" value="0.8"/><!-- Percent Navigation for Altitude Error Equal to Start Altitude -->
   <define name="DESCENT_NAV_RATIO" value="1.0"/>
   </section>


 <section name="FAILSAFE" prefix="FAILSAFE_">
   <define name="DELAY_WITHOUT_GPS" value="1" unit="s"/>
       <define name="DEFAULT_THROTTLE" value="0.3" unit="%"/>
       <define name="DEFAULT_ROLL" value="0.3" unit="rad"/>
       <define name="DEFAULT_PITCH" value="0.5" unit="rad"/>
   <define name="HOME_RADIUS" value="100" unit="m"/>
</section>
 <!--
 <section name="DATALINK" prefix="DATALINK_">
   <define name="DEVICE_TYPE" value="PPRZ"/>
   <define name="DEVICE_ADDRESS" value="...."/>
 </section>
-->


 <makefile>
include $(PAPARAZZI_SRC)/conf/autopilot/tiny.makefile

FLASH_MODE=IAP

ap.CFLAGS +=  -DFBW -DAP -DCONFIG=\"tiny.h\" -DLED -DTIME_LED=1
ap.srcs = sys_time.c $(SRC_ARCH)/sys_time_hw.c $(SRC_ARCH)/armVIC.c main_fbw.c main_ap.c main.c

ap.CFLAGS += -DLED_3_BANK=0 -DLED_3_PIN=17 -DLED_4_BANK=0 -DLED_4_PIN=18 -DLED_5_BANK=0 -DLED_5_PIN=19 -DLED_6_BANK=0 -DLED_6_PIN=20


ap.srcs += commands.c

ap.CFLAGS += -DACTUATORS=\"servos_4015_hw.h\" -DSERVOS_4015
ap.srcs += actuators.c $(SRC_ARCH)/servos_4015_hw.c

ap.CFLAGS += -DRADIO_CONTROL -DRADIO_CONTROL_TYPE=RC_JR
ap.srcs += radio_control.c $(SRC_ARCH)/ppm_hw.c
ap.CFLAGS += -DDOWNLINK -DUSE_UART0 -DDOWNLINK_TRANSPORT=PprzTransport -DDOWNLINK_FBW_DEVICE=Uart0 -DDOWNLINK_AP_DEVICE=Uart0 -DPPRZ_UART=Uart0 -DDATALINK=PPRZ -DUART0_BAUD=B9600
ap.srcs += downlink.c $(SRC_ARCH)/uart_hw.c datalink.c pprz_transport.c latlong.c


ap.CFLAGS += -DINTER_MCU
ap.srcs += inter_mcu.c

ap.CFLAGS += -DADC -DUSE_AD0 -DUSE_AD0_2 -DUSE_AD0_3 -DUSE_AD1 -DUSE_AD1_5 -DUSE_AD1_3 -DUSE_AD1_5
ap.srcs += $(SRC_ARCH)/adc_hw.c

ap.CFLAGS += -DGPS -DUBX -DUSE_UART1 -DGPS_LINK=Uart1 -DUART1_BAUD=B9600

ap.srcs += gps_ubx.c gps.c

ap.CFLAGS += -DINFRARED
ap.srcs += infrared.c estimator.c

ap.CFLAGS += -DNAV
ap.srcs += nav.c fw_h_ctl.c fw_v_ctl.c nav_survey_rectangle.c nav_line.c


ap.CFLAGS += -DGYRO -DADXRS150 -DPID_RATE_LOOP
ap.srcs += gyro.c

# Harware In The Loop

#ap.CFLAGS += -DHITL

# Config for SITL simulation
include $(PAPARAZZI_SRC)/conf/autopilot/sitl.makefile
sim.CFLAGS += -DCONFIG=\"tiny.h\" -DAGR_CLIMB -DLOITER_TRIM -DALT_KALMAN
sim.srcs += nav_survey_rectangle.c traffic_info.c nav_line.c
 </makefile>
</airframe>

------------------------------------------------------------------------


_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
 



_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel



reply via email to

[Prev in Thread] Current Thread [Next in Thread]