[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] i2c voltage level

From: Refik Sever
Subject: Re: [Paparazzi-devel] i2c voltage level
Date: Tue, 20 Aug 2013 01:00:10 +0300

Hi Martin,

I just ordered 5 of them.


>-----Original Message-----
>From: address@hidden
[mailto:address@hidden On
Behalf Of Martin Mueller
>Sent: Tuesday, August 20, 2013 12:31 AM
>To: address@hidden
>Subject: Re: [Paparazzi-devel] i2c voltage level
>Hi Refik,
> I understand that drotek i2c signals are using 3.3v, therefore no problem
for drotek.
> I also want to add SRF08 ultrasonic sensor to the other I2C bus. SRF08
works with 5V, and I2C signals are also at 5V. On the same bus, I also
connected TMP102 temp. sensor and ETS airspeed sensor. They all use 3.3V i2c
signals, and they all get their supply from autopilot.
> I understand from your emails that digital i/o pins of LPC2148/stm32 are
5V compatible, therefore no problem for the autopilot. Will there be a
problem for tmp102 and ets airspeed sensors?

>Yes. Add a 5V <-> 3.3V level shifter for the SRF08, see the TEMOD module
for an example


> Best regards,
> Refik
>> From: address@hidden 
>> [mailto:address@hidden 
>> On Behalf Of Prof. Dr.-Ing. Heinrich >Warmers
>> Sent: Monday, August 19, 2013 6:00 PM
> To: address@hidden
> Subject: Re: [Paparazzi-devel] i2c voltage level
> Hi,
> if you supply the imu with 3.3V it works with 3V i2c.
> If you supply it with 5V it works with 5V i2c.
> But you may destroy the 3V i2c components if you connect them with 5V i2c.
> The lpc2148 is 5V compatible if it is supplied with 3.3V.
> If you power on the i2c brush less controller (5V)  and the lpc2148 has no
power you will destroy the LPC2148.
> The stm32 pins are only 5V compatible if the processor is supplied.
> The maximum level is 4V if there is no power on the processor.
> Heinrich
> -----Original Message-----
> From: address@hidden 
> [mailto:address@hidden 
> On Behalf Of Martin Mueller
> Sent: Monday, August 19, 2013 6:24 PM
> To: address@hidden
> Subject: Re: [Paparazzi-devel] i2c voltage level
> Hi Refik,
>> We have bought Drotek 10dof IMU, and the module works with 5V.  Do 
>> the I2C pins of drotek also work with 5V?
> the board is supplied with 5V but the sensors run on 3.3V and so do the
I2C lines. An on-board linear 5V -> 3.3V regulator is used to have a clean
3.3V supply (see imu-10dof-mpu6050-hmc5883-ms5611.PDF).
>> Are the I2C pins of LPC2148 and STM32 processors compatible with 5V?
> The digital LPC2148/STM32 pins are claimed to be 5V tolerant (not the LPC
ADC input pins) but it is good practice not to run them at 5V.
> Never apply a voltage to any pin of a chip that is not powered through the
supply voltage.
> Martin
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden

Paparazzi-devel mailing list

reply via email to

[Prev in Thread] Current Thread [Next in Thread]