poke-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

☠ Buildbot (Sourceware): gnupoke - failed test (failure) (master)


From: builder
Subject: ☠ Buildbot (Sourceware): gnupoke - failed test (failure) (master)
Date: Fri, 03 Feb 2023 00:35:28 +0000

A new failure has been detected on builder gnupoke-debian-i386 while building 
gnupoke.

Full details are available at:
    https://builder.sourceware.org/buildbot/#builders/219/builds/154

Build state: failed test (failure)
Revision: 8a5ec2e6b0d58638208d70cb9b38c8f56e676bb9
Worker: debian-i386-2
Build Reason: (unknown)
Blamelist: Jose E. Marchesi <jose.marchesi@oracle.com>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/1/logs/stdio

- 2: bootstrap ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/3/logs/stdio
        - config.log: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/3/logs/config_log

- 4: make ( warnings )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/4/logs/stdio
        - warnings (4): 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/4/logs/warnings__4_

- 5: make check ( failure )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/5/logs/stdio

- 6: make syntax-check ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/6/logs/stdio

- 7: prep ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/7/logs/stdio

- 8: build bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/8/logs/stdio

- 9: fetch bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/9/logs/stdio

- 10: unpack bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/10/logs/stdio

- 11: pass .bunsen.source.gitname ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/11/logs/stdio

- 12: pass .bunsen.source.gitdescribe ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/12/logs/stdio

- 13: pass .bunsen.source.gitbranch ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/13/logs/stdio

- 14: pass .bunsen.source.gitrepo ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/14/logs/stdio

- 15: upload to bunsen ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/15/logs/stdio

- 16: clean up ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/154/steps/16/logs/stdio




reply via email to

[Prev in Thread] Current Thread [Next in Thread]