[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [PATCH 1/9] hw/block/pflash_cfi: Fix code style for checkpatch.pl
From: |
David Edmondson |
Subject: |
Re: [PATCH 1/9] hw/block/pflash_cfi: Fix code style for checkpatch.pl |
Date: |
Wed, 10 Mar 2021 09:30:01 +0000 |
On Wednesday, 2021-03-10 at 00:50:20 +01, Philippe Mathieu-Daudé wrote:
> We are going to move this code, fix its style first.
>
> Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
> ---
> hw/block/pflash_cfi01.c | 36 ++++++++++++++++++++++++------------
> hw/block/pflash_cfi02.c | 9 ++++++---
> 2 files changed, 30 insertions(+), 15 deletions(-)
>
> diff --git a/hw/block/pflash_cfi01.c b/hw/block/pflash_cfi01.c
> index 22287a1522e..b6919bbe474 100644
> --- a/hw/block/pflash_cfi01.c
> +++ b/hw/block/pflash_cfi01.c
> @@ -115,7 +115,8 @@ static const VMStateDescription vmstate_pflash = {
> }
> };
>
> -/* Perform a CFI query based on the bank width of the flash.
> +/*
> + * Perform a CFI query based on the bank width of the flash.
> * If this code is called we know we have a device_width set for
> * this flash.
> */
> @@ -125,7 +126,8 @@ static uint32_t pflash_cfi_query(PFlashCFI01 *pfl, hwaddr
> offset)
> uint32_t resp = 0;
> hwaddr boff;
>
> - /* Adjust incoming offset to match expected device-width
> + /*
> + * Adjust incoming offset to match expected device-width
> * addressing. CFI query addresses are always specified in terms of
> * the maximum supported width of the device. This means that x8
> * devices and x8/x16 devices in x8 mode behave differently. For
> @@ -141,7 +143,8 @@ static uint32_t pflash_cfi_query(PFlashCFI01 *pfl, hwaddr
> offset)
> if (boff >= sizeof(pfl->cfi_table)) {
> return 0;
> }
> - /* Now we will construct the CFI response generated by a single
> + /*
> + * Now we will construct the CFI response generated by a single
> * device, then replicate that for all devices that make up the
> * bus. For wide parts used in x8 mode, CFI query responses
> * are different than native byte-wide parts.
> @@ -185,7 +188,8 @@ static uint32_t pflash_devid_query(PFlashCFI01 *pfl,
> hwaddr offset)
> uint32_t resp;
> hwaddr boff;
>
> - /* Adjust incoming offset to match expected device-width
> + /*
> + * Adjust incoming offset to match expected device-width
> * addressing. Device ID read addresses are always specified in
> * terms of the maximum supported width of the device. This means
> * that x8 devices and x8/x16 devices in x8 mode behave
> @@ -198,7 +202,8 @@ static uint32_t pflash_devid_query(PFlashCFI01 *pfl,
> hwaddr offset)
> boff = offset >> (ctz32(pfl->bank_width) +
> ctz32(pfl->max_device_width) -
> ctz32(pfl->device_width));
>
> - /* Mask off upper bits which may be used in to query block
> + /*
> + * Mask off upper bits which may be used in to query block
> * or sector lock status at other addresses.
> * Offsets 2/3 are block lock status, is not emulated.
> */
> @@ -297,7 +302,8 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr
> offset,
> case 0x60: /* Block /un)lock */
> case 0x70: /* Status Register */
> case 0xe8: /* Write block */
> - /* Status register read. Return status from each device in
> + /*
> + * Status register read. Return status from each device in
> * bank.
> */
> ret = pfl->status;
> @@ -308,7 +314,8 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr
> offset,
> shift += pfl->device_width * 8;
> }
> } else if (!pfl->device_width && width > 2) {
> - /* Handle 32 bit flash cases where device width is not
> + /*
> + * Handle 32 bit flash cases where device width is not
> * set. (Existing behavior before device width added.)
> */
> ret |= pfl->status << 16;
> @@ -340,7 +347,8 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr
> offset,
> break;
> }
> } else {
> - /* If we have a read larger than the bank_width, combine multiple
> + /*
> + * If we have a read larger than the bank_width, combine multiple
> * manufacturer/device ID queries into a single response.
> */
> int i;
> @@ -367,7 +375,8 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr
> offset,
> ret = 0;
> }
> } else {
> - /* If we have a read larger than the bank_width, combine multiple
> + /*
> + * If we have a read larger than the bank_width, combine multiple
> * CFI queries into a single response.
> */
> int i;
> @@ -544,7 +553,8 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
>
> break;
> case 0xe8:
> - /* Mask writeblock size based on device width, or bank width if
> + /*
> + * Mask writeblock size based on device width, or bank width if
> * device width not specified.
> */
> /* FIXME check @offset, @width */
> @@ -718,7 +728,8 @@ static void pflash_cfi01_realize(DeviceState *dev, Error
> **errp)
>
> total_len = pfl->sector_len * pfl->nb_blocs;
>
> - /* These are only used to expose the parameters of each device
> + /*
> + * These are only used to expose the parameters of each device
> * in the cfi_table[].
> */
> num_devices = pfl->device_width ? (pfl->bank_width / pfl->device_width)
> : 1;
> @@ -763,7 +774,8 @@ static void pflash_cfi01_realize(DeviceState *dev, Error
> **errp)
> }
> }
>
> - /* Default to devices being used at their maximum device width. This was
> + /*
> + * Default to devices being used at their maximum device width. This was
> * assumed before the device_width support was added.
> */
> if (!pfl->max_device_width) {
> diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
> index 7962cff7455..fa981465e12 100644
> --- a/hw/block/pflash_cfi02.c
> +++ b/hw/block/pflash_cfi02.c
> @@ -100,7 +100,8 @@ struct PFlashCFI02 {
> uint16_t unlock_addr1;
> uint8_t cfi_table[0x4d];
> QEMUTimer timer;
> - /* The device replicates the flash memory across its memory space.
> Emulate
> + /*
> + * The device replicates the flash memory across its memory space.
> Emulate
> * that by having a container (.mem) filled with an array of aliases
> * (.mem_mappings) pointing to the flash memory (.orig_mem).
> */
> @@ -884,8 +885,10 @@ static void pflash_cfi02_realize(DeviceState *dev, Error
> **errp)
> pfl->cfi_table[0x28] = 0x02;
> pfl->cfi_table[0x29] = 0x00;
> /* Max number of bytes in multi-bytes write */
> - /* XXX: disable buffered write as it's not supported */
> - // pfl->cfi_table[0x2A] = 0x05;
> + /*
> + * XXX: disable buffered write as it's not supported
> + * pfl->cfi_table[0x2A] = 0x05;
> + */
> pfl->cfi_table[0x2A] = 0x00;
> pfl->cfi_table[0x2B] = 0x00;
> /* Number of erase block regions */
> --
> 2.26.2
dme.
--
You're like my yo-yo, that glowed in the dark.