[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] [PATCH] 8250: more realistic TX-done IRQ rate
From: |
Jan Kiszka |
Subject: |
[Qemu-devel] [PATCH] 8250: more realistic TX-done IRQ rate |
Date: |
Sat, 12 Apr 2008 16:56:46 +0200 |
User-agent: |
Thunderbird 2.0.0.12 (X11/20080226) |
The 8250 UART emulation currently raises a TX-done IRQ immediately when the guest writes
out some character. This is problematic for guests like Linux which may flush its output
buffer in a loop from IRQ context, because they may then enter a tight loop with IRQs
disabled. In fact, Linux breaks out of this loop after some iterations and issue the
well-known [1] "too much work for irq..." warning. And in case the console
output is on the very same serial port, the console output is utterly corrupted.
Patch below addresses the issue by delaying the TX-done IRQ more realistically,
ie. according to the currently set baudrate.
Jan
[1] http://lkml.org/lkml/2008/1/12/135
Signed-off-by: Jan Kiszka <address@hidden>
---
hw/serial.c | 39 ++++++++++++++++++++++++++++-----------
1 file changed, 28 insertions(+), 11 deletions(-)
Index: b/hw/serial.c
===================================================================
--- a/hw/serial.c
+++ b/hw/serial.c
@@ -25,6 +25,7 @@
#include "qemu-char.h"
#include "isa.h"
#include "pc.h"
+#include "qemu-timer.h"
//#define DEBUG_SERIAL
@@ -91,6 +92,8 @@ struct SerialState {
int last_break_enable;
target_phys_addr_t base;
int it_shift;
+ QEMUTimer *tx_timer;
+ char tx_buf;
};
static void serial_receive_byte(SerialState *s, int ch);
@@ -111,6 +114,20 @@ static void serial_update_irq(SerialStat
}
}
+static void serial_tx_done(void *opaque)
+{
+ SerialState *s = opaque;
+
+ s->thr_ipending = 1;
+ s->lsr |= UART_LSR_THRE;
+ s->lsr |= UART_LSR_TEMT;
+ serial_update_irq(s);
+ if (s->mcr & UART_MCR_LOOP) {
+ /* in loopback mode, say that we just received a char */
+ serial_receive_byte(s, s->tx_buf);
+ }
+}
+
static void serial_update_parameters(SerialState *s)
{
int speed, parity, data_bits, stop_bits;
@@ -146,7 +163,6 @@ static void serial_update_parameters(Ser
static void serial_ioport_write(void *opaque, uint32_t addr, uint32_t val)
{
SerialState *s = opaque;
- unsigned char ch;
addr &= 7;
#ifdef DEBUG_SERIAL
@@ -162,19 +178,12 @@ static void serial_ioport_write(void *op
s->thr_ipending = 0;
s->lsr &= ~UART_LSR_THRE;
serial_update_irq(s);
- ch = val;
+ s->tx_buf = val;
if (!(s->mcr & UART_MCR_LOOP)) {
/* when not in loopback mode, send the char */
- qemu_chr_write(s->chr, &ch, 1);
- }
- s->thr_ipending = 1;
- s->lsr |= UART_LSR_THRE;
- s->lsr |= UART_LSR_TEMT;
- serial_update_irq(s);
- if (s->mcr & UART_MCR_LOOP) {
- /* in loopback mode, say that we just received a char */
- serial_receive_byte(s, ch);
+ qemu_chr_write(s->chr, &s->tx_buf, 1);
}
+ qemu_mod_timer(s->tx_timer, 1000 / (11520 / s->divider));
}
break;
case 1:
@@ -387,6 +396,10 @@ SerialState *serial_init(int base, qemu_
return NULL;
s->irq = irq;
+ s->tx_timer = qemu_new_timer(vm_clock, serial_tx_done, s);
+ if (!s->tx_timer)
+ return NULL;
+
qemu_register_reset(serial_reset, s);
serial_reset(s);
@@ -486,6 +499,10 @@ SerialState *serial_mm_init (target_phys
s->base = base;
s->it_shift = it_shift;
+ s->tx_timer = qemu_new_timer(vm_clock, serial_tx_done, s);
+ if (!s->tx_timer)
+ return NULL;
+
qemu_register_reset(serial_reset, s);
serial_reset(s);
signature.asc
Description: OpenPGP digital signature
- [Qemu-devel] [PATCH] 8250: more realistic TX-done IRQ rate,
Jan Kiszka <=