qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PATCHv3 2/4] shpc: standard hot plug controller


From: Michael S. Tsirkin
Subject: [Qemu-devel] [PATCHv3 2/4] shpc: standard hot plug controller
Date: Tue, 21 Feb 2012 00:53:02 +0200
User-agent: Mutt/1.5.21 (2010-09-15)

This adds support for SHPC interface, as defined by PCI Standard
Hot-Plug Controller and Subsystem Specification, Rev 1.0
http://www.pcisig.com/specifications/conventional/pci_hot_plug/SHPC_10

Only SHPC intergrated with a PCI-to-PCI bridge is supported,
SHPC integrated with a host bridge would need more work.

All main SHPC features are supported:
- MRL sensor
- Attention button
- Attention indicator
- Power indicator

Wake on hotplug and serr generation are stubbed out but unused
as we don't have interfaces to generate these events ATM.

One issue that isn't completely resolved is that qemu currently
expects an "eject" interface, which SHPC does not provide: it merely
removes the power to device and it's up to the user to remove the device
from slot. This patch works around that by ejecting the device
when power is removed and power LED goes off.

Signed-off-by: Michael S. Tsirkin <address@hidden>
---
 Makefile.objs |    1 +
 hw/pci.h      |    6 +
 hw/shpc.c     |  673 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 hw/shpc.h     |   45 ++++
 qemu-common.h |    1 +
 5 files changed, 726 insertions(+), 0 deletions(-)
 create mode 100644 hw/shpc.c
 create mode 100644 hw/shpc.h

diff --git a/Makefile.objs b/Makefile.objs
index 391e524..4546477 100644
--- a/Makefile.objs
+++ b/Makefile.objs
@@ -195,6 +195,7 @@ hw-obj-$(CONFIG_VIRTIO_PCI) += virtio-pci.o
 hw-obj-y += fw_cfg.o
 hw-obj-$(CONFIG_PCI) += pci.o pci_bridge.o
 hw-obj-$(CONFIG_PCI) += msix.o msi.o
+hw-obj-$(CONFIG_PCI) += shpc.o
 hw-obj-$(CONFIG_PCI) += pci_host.o pcie_host.o
 hw-obj-$(CONFIG_PCI) += ioh3420.o xio3130_upstream.o xio3130_downstream.o
 hw-obj-y += watchdog.o
diff --git a/hw/pci.h b/hw/pci.h
index 2a29654..05a7ebb 100644
--- a/hw/pci.h
+++ b/hw/pci.h
@@ -125,6 +125,9 @@ enum {
     /* command register SERR bit enabled */
 #define QEMU_PCI_CAP_SERR_BITNR 4
     QEMU_PCI_CAP_SERR = (1 << QEMU_PCI_CAP_SERR_BITNR),
+    /* Standard hot plug controller. */
+#define QEMU_PCI_SHPC_BITNR 5
+    QEMU_PCI_CAP_SHPC = (1 << QEMU_PCI_SHPC_BITNR),
 };
 
 #define TYPE_PCI_DEVICE "pci-device"
@@ -229,6 +232,9 @@ struct PCIDevice {
     /* PCI Express */
     PCIExpressDevice exp;
 
+    /* SHPC */
+    SHPCDevice *shpc;
+
     /* Location of option rom */
     char *romfile;
     bool has_rom;
diff --git a/hw/shpc.c b/hw/shpc.c
new file mode 100644
index 0000000..d731096
--- /dev/null
+++ b/hw/shpc.c
@@ -0,0 +1,673 @@
+#include <strings.h>
+#include <stdint.h>
+#include "range.h"
+#include "shpc.h"
+#include "pci.h"
+#include "pci_internals.h"
+
+/* TODO: model power only and disabled slot states. */
+/* TODO: handle SERR and wakeups */
+/* TODO: consider enabling 66MHz support */
+
+/* TODO: remove fully only on state DISABLED and LED off.
+ * track state to properly record this. */
+
+/* SHPC Working Register Set */
+#define SHPC_BASE_OFFSET  0x00 /* 4 bytes */
+#define SHPC_SLOTS_33     0x04 /* 4 bytes. Also encodes PCI-X slots. */
+#define SHPC_SLOTS_66     0x08 /* 4 bytes. */
+#define SHPC_NSLOTS       0x0C /* 1 byte */
+#define SHPC_FIRST_DEV    0x0D /* 1 byte */
+#define SHPC_PHYS_SLOT    0x0E /* 2 byte */
+#define SHPC_PHYS_NUM_MAX 0x7ff
+#define SHPC_PHYS_NUM_UP  0x2000
+#define SHPC_PHYS_MRL     0x4000
+#define SHPC_PHYS_BUTTON  0x8000
+#define SHPC_SEC_BUS      0x10 /* 2 bytes */
+#define SHPC_SEC_BUS_33   0x0
+#define SHPC_SEC_BUS_66   0x1 /* Unused */
+#define SHPC_SEC_BUS_MASK 0x7
+#define SHPC_MSI_CTL      0x12 /* 1 byte */
+#define SHPC_PROG_IFC     0x13 /* 1 byte */
+#define SHPC_PROG_IFC_1_0 0x1
+#define SHPC_CMD_CODE     0x14 /* 1 byte */
+#define SHPC_CMD_TRGT     0x15 /* 1 byte */
+#define SHPC_CMD_TRGT_MIN 0x1
+#define SHPC_CMD_TRGT_MAX 0x1f
+#define SHPC_CMD_STATUS   0x16 /* 2 bytes */
+#define SHPC_CMD_STATUS_BUSY          0x1
+#define SHPC_CMD_STATUS_MRL_OPEN      0x2
+#define SHPC_CMD_STATUS_INVALID_CMD   0x4
+#define SHPC_CMD_STATUS_INVALID_MODE  0x8
+#define SHPC_INT_LOCATOR  0x18 /* 4 bytes */
+#define SHPC_INT_COMMAND  0x1
+#define SHPC_SERR_LOCATOR 0x1C /* 4 bytes */
+#define SHPC_SERR_INT     0x20 /* 4 bytes */
+#define SHPC_INT_DIS      0x1
+#define SHPC_SERR_DIS     0x2
+#define SHPC_CMD_INT_DIS  0x4
+#define SHPC_ARB_SERR_DIS 0x8
+#define SHPC_CMD_DETECTED 0x10000
+#define SHPC_ARB_DETECTED 0x20000
+ /* 4 bytes * slot # (start from 0) */
+#define SHPC_SLOT_REG(s)         (0x24 + (s) * 4)
+ /* 2 bytes */
+#define SHPC_SLOT_STATUS(s)       (0x0 + SHPC_SLOT_REG(s))
+
+/* Same slot state masks are used for command and status registers */
+#define SHPC_SLOT_STATE_MASK     0x03
+#define SHPC_SLOT_STATE_SHIFT \
+    (ffs(SHPC_SLOT_STATE_MASK) - 1)
+
+#define SHPC_STATE_NO       0x0
+#define SHPC_STATE_PWRONLY  0x1
+#define SHPC_STATE_ENABLED  0x2
+#define SHPC_STATE_DISABLED 0x3
+
+#define SHPC_SLOT_PWR_LED_MASK   0xC
+#define SHPC_SLOT_PWR_LED_SHIFT \
+    (ffs(SHPC_SLOT_PWR_LED_MASK) - 1)
+#define SHPC_SLOT_ATTN_LED_MASK  0x30
+#define SHPC_SLOT_ATTN_LED_SHIFT \
+    (ffs(SHPC_SLOT_ATTN_LED_MASK) - 1)
+
+#define SHPC_LED_NO     0x0
+#define SHPC_LED_ON     0x1
+#define SHPC_LED_BLINK  0x2
+#define SHPC_LED_OFF    0x3
+
+#define SHPC_SLOT_STATUS_PWR_FAULT      0x40
+#define SHPC_SLOT_STATUS_BUTTON         0x80
+#define SHPC_SLOT_STATUS_MRL_OPEN       0x100
+#define SHPC_SLOT_STATUS_66             0x200
+#define SHPC_SLOT_STATUS_PRSNT_MASK     0xC00
+#define SHPC_SLOT_STATUS_PRSNT_EMPTY    0x3
+#define SHPC_SLOT_STATUS_PRSNT_25W      0x1
+#define SHPC_SLOT_STATUS_PRSNT_15W      0x2
+#define SHPC_SLOT_STATUS_PRSNT_7_5W     0x0
+
+#define SHPC_SLOT_STATUS_PRSNT_PCIX     0x3000
+
+
+ /* 1 byte */
+#define SHPC_SLOT_EVENT_LATCH(s)        (0x2 + SHPC_SLOT_REG(s))
+ /* 1 byte */
+#define SHPC_SLOT_EVENT_SERR_INT_DIS(d, s) (0x3 + SHPC_SLOT_REG(s))
+#define SHPC_SLOT_EVENT_PRESENCE        0x01
+#define SHPC_SLOT_EVENT_ISOLATED_FAULT  0x02
+#define SHPC_SLOT_EVENT_BUTTON          0x04
+#define SHPC_SLOT_EVENT_MRL             0x08
+#define SHPC_SLOT_EVENT_CONNECTED_FAULT 0x10
+/* Bits below are used for Serr/Int disable only */
+#define SHPC_SLOT_EVENT_MRL_SERR_DIS    0x20
+#define SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS 0x40
+
+#define SHPC_MIN_SLOTS        1
+#define SHPC_MAX_SLOTS        31
+#define SHPC_SIZEOF(d)    SHPC_SLOT_REG((d)->shpc->nslots)
+
+/* SHPC Slot identifiers */
+
+/* Hotplug supported at 31 slots out of the total 32.  We reserve slot 0,
+   and give the rest of them physical *and* pci numbers starting from 1, so
+   they match logical numbers.  Note: this means that multiple slots must have
+   different chassis number values, to make chassis+physical slot unique.
+   TODO: make this configurable? */
+#define SHPC_IDX_TO_LOGICAL(slot) ((slot) + 1)
+#define SHPC_LOGICAL_TO_IDX(target) ((target) - 1)
+#define SHPC_IDX_TO_PCI(slot) ((slot) + 1)
+#define SHPC_PCI_TO_IDX(pci_slot) ((pci_slot) - 1)
+#define SHPC_IDX_TO_PHYSICAL(slot) ((slot) + 1)
+
+static int roundup_pow_of_two(int x)
+{
+    x |= (x >> 1);
+    x |= (x >> 2);
+    x |= (x >> 4);
+    x |= (x >> 8);
+    x |= (x >> 16);
+    return x + 1;
+}
+
+static uint16_t shpc_get_status(SHPCDevice *shpc, int slot, uint16_t msk)
+{
+    uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot);
+    return (pci_get_word(status) & msk) >> (ffs(msk) - 1);
+}
+
+static void shpc_set_status(SHPCDevice *shpc,
+                            int slot, uint8_t value, uint16_t msk)
+{
+    uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot);
+    pci_word_test_and_clear_mask(status, msk);
+    pci_word_test_and_set_mask(status, value << (ffs(msk) - 1));
+}
+
+static void shpc_interrupt_update(PCIDevice *d)
+{
+    SHPCDevice *shpc = d->shpc;
+    int slot;
+    int level = 0;
+    uint32_t serr_int;
+    uint32_t int_locator = 0;
+
+    /* Update interrupt locator register */
+    for (slot = 0; slot < shpc->nslots; ++slot) {
+        uint8_t event = shpc->config[SHPC_SLOT_EVENT_LATCH(slot)];
+        uint8_t disable = shpc->config[SHPC_SLOT_EVENT_SERR_INT_DIS(d, slot)];
+        uint32_t mask = 1 << SHPC_IDX_TO_LOGICAL(slot);
+        if (event & ~disable) {
+            int_locator |= mask;
+        }
+    }
+    serr_int = pci_get_long(shpc->config + SHPC_SERR_INT);
+    if ((serr_int & SHPC_CMD_DETECTED) && !(serr_int & SHPC_CMD_INT_DIS)) {
+        int_locator |= SHPC_INT_COMMAND;
+    }
+    pci_set_long(shpc->config + SHPC_INT_LOCATOR, int_locator);
+    level = (!(serr_int & SHPC_INT_DIS) && int_locator) ? 1 : 0;
+    qemu_set_irq(d->irq[0], level);
+}
+
+static void shpc_set_sec_bus_speed(SHPCDevice *shpc, uint8_t speed)
+{
+    switch (speed) {
+    case SHPC_SEC_BUS_33:
+        shpc->config[SHPC_SEC_BUS] &= ~SHPC_SEC_BUS_MASK;
+        shpc->config[SHPC_SEC_BUS] |= speed;
+        break;
+    default:
+        pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS,
+                                   SHPC_CMD_STATUS_INVALID_MODE);
+    }
+}
+
+void shpc_reset(PCIDevice *d)
+{
+    SHPCDevice *shpc = d->shpc;
+    int nslots = shpc->nslots;
+    int i;
+    memset(shpc->config, 0, SHPC_SIZEOF(d));
+    pci_set_byte(shpc->config + SHPC_NSLOTS, nslots);
+    pci_set_long(shpc->config + SHPC_SLOTS_33, nslots);
+    pci_set_long(shpc->config + SHPC_SLOTS_66, 0);
+    pci_set_byte(shpc->config + SHPC_FIRST_DEV, SHPC_IDX_TO_PCI(0));
+    pci_set_word(shpc->config + SHPC_PHYS_SLOT,
+                 SHPC_IDX_TO_PHYSICAL(0) |
+                 SHPC_PHYS_NUM_UP |
+                 SHPC_PHYS_MRL |
+                 SHPC_PHYS_BUTTON);
+    pci_set_long(shpc->config + SHPC_SERR_INT, SHPC_INT_DIS |
+                 SHPC_SERR_DIS |
+                 SHPC_CMD_INT_DIS |
+                 SHPC_ARB_SERR_DIS);
+    pci_set_byte(shpc->config + SHPC_PROG_IFC, SHPC_PROG_IFC_1_0);
+    pci_set_word(shpc->config + SHPC_SEC_BUS, SHPC_SEC_BUS_33);
+    for (i = 0; i < shpc->nslots; ++i) {
+        pci_set_word(shpc->config + SHPC_SLOT_EVENT_SERR_INT_DIS(d, i),
+                     SHPC_SLOT_EVENT_PRESENCE |
+                     SHPC_SLOT_EVENT_ISOLATED_FAULT |
+                     SHPC_SLOT_EVENT_BUTTON |
+                     SHPC_SLOT_EVENT_MRL |
+                     SHPC_SLOT_EVENT_CONNECTED_FAULT |
+                     SHPC_SLOT_EVENT_MRL_SERR_DIS |
+                     SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS);
+        if (shpc->sec_bus->devices[PCI_DEVFN(SHPC_IDX_TO_PCI(i), 0)]) {
+            shpc_set_status(shpc, i, SHPC_STATE_ENABLED, SHPC_SLOT_STATE_MASK);
+            shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_MRL_OPEN);
+            shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_7_5W,
+                            SHPC_SLOT_STATUS_PRSNT_MASK);
+            shpc_set_status(shpc, i, SHPC_LED_ON, SHPC_SLOT_PWR_LED_MASK);
+        } else {
+            shpc_set_status(shpc, i, SHPC_STATE_DISABLED, 
SHPC_SLOT_STATE_MASK);
+            shpc_set_status(shpc, i, 1, SHPC_SLOT_STATUS_MRL_OPEN);
+            shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_EMPTY,
+                            SHPC_SLOT_STATUS_PRSNT_MASK);
+            shpc_set_status(shpc, i, SHPC_LED_OFF, SHPC_SLOT_PWR_LED_MASK);
+        }
+        shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_66);
+    }
+    shpc_set_sec_bus_speed(shpc, SHPC_SEC_BUS_33);
+    shpc_interrupt_update(d);
+}
+
+static void shpc_invalid_command(SHPCDevice *shpc)
+{
+    pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS,
+                               SHPC_CMD_STATUS_INVALID_CMD);
+}
+
+static void shpc_free_devices_in_slot(SHPCDevice *shpc, int slot)
+{
+    int devfn;
+    int pci_slot = SHPC_IDX_TO_PCI(slot);
+    for (devfn = PCI_DEVFN(pci_slot, 0);
+         devfn <= PCI_DEVFN(pci_slot, PCI_FUNC_MAX - 1);
+         ++devfn) {
+        PCIDevice *affected_dev = shpc->sec_bus->devices[devfn];
+        if (affected_dev) {
+            qdev_free(&affected_dev->qdev);
+        }
+    }
+}
+
+static void shpc_slot_command(SHPCDevice *shpc, uint8_t target,
+                              uint8_t state, uint8_t power, uint8_t attn)
+{
+    uint8_t current_state;
+    int slot = SHPC_LOGICAL_TO_IDX(target);
+    if (target < SHPC_CMD_TRGT_MIN || slot >= shpc->nslots) {
+        shpc_invalid_command(shpc);
+        return;
+    }
+    current_state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK);
+    if (current_state == SHPC_STATE_ENABLED && state == SHPC_STATE_PWRONLY) {
+        shpc_invalid_command(shpc);
+        return;
+    }
+
+    switch (power) {
+    case SHPC_LED_NO:
+        break;
+    default:
+        /* TODO: send event to monitor */
+        shpc_set_status(shpc, slot, power, SHPC_SLOT_PWR_LED_MASK);
+    }
+    switch (attn) {
+    case SHPC_LED_NO:
+        break;
+    default:
+        /* TODO: send event to monitor */
+        shpc_set_status(shpc, slot, attn, SHPC_SLOT_ATTN_LED_MASK);
+    }
+
+    if ((current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_PWRONLY) 
||
+        (current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_ENABLED)) 
{
+        shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK);
+    } else if ((current_state == SHPC_STATE_ENABLED ||
+                current_state == SHPC_STATE_PWRONLY) &&
+               state == SHPC_STATE_DISABLED) {
+        shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK);
+        power = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK);
+        /* TODO: track what monitor requested. */
+        /* Look at LED to figure out whether it's ok to remove the device. */
+        if (power == SHPC_LED_OFF) {
+            shpc_free_devices_in_slot(shpc, slot);
+            shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN);
+            shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY,
+                            SHPC_SLOT_STATUS_PRSNT_MASK);
+            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
+                SHPC_SLOT_EVENT_BUTTON |
+                SHPC_SLOT_EVENT_MRL |
+                SHPC_SLOT_EVENT_PRESENCE;
+        }
+    }
+}
+
+static void shpc_command(SHPCDevice *shpc)
+{
+    uint8_t code = pci_get_byte(shpc->config + SHPC_CMD_CODE);
+    uint8_t speed;
+    uint8_t target;
+    uint8_t attn;
+    uint8_t power;
+    uint8_t state;
+    int i;
+
+    /* Clear status from the previous command. */
+    pci_word_test_and_clear_mask(shpc->config + SHPC_CMD_STATUS,
+                                 SHPC_CMD_STATUS_BUSY |
+                                 SHPC_CMD_STATUS_MRL_OPEN |
+                                 SHPC_CMD_STATUS_INVALID_CMD |
+                                 SHPC_CMD_STATUS_INVALID_MODE);
+    switch (code) {
+    case 0x00 ... 0x3f:
+        target = shpc->config[SHPC_CMD_TRGT] & SHPC_CMD_TRGT_MAX;
+        state = (code & SHPC_SLOT_STATE_MASK) >> SHPC_SLOT_STATE_SHIFT;
+        power = (code & SHPC_SLOT_PWR_LED_MASK) >> SHPC_SLOT_PWR_LED_SHIFT;
+        attn = (code & SHPC_SLOT_ATTN_LED_MASK) >> SHPC_SLOT_ATTN_LED_SHIFT;
+        shpc_slot_command(shpc, target, state, power, attn);
+        break;
+    case 0x40 ... 0x47:
+        speed = code & SHPC_SEC_BUS_MASK;
+        shpc_set_sec_bus_speed(shpc, speed);
+        break;
+    case 0x48:
+        /* Power only all slots */
+        /* first verify no slots are enabled */
+        for (i = 0; i < shpc->nslots; ++i) {
+            state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK);
+            if (state == SHPC_STATE_ENABLED) {
+                shpc_invalid_command(shpc);
+                goto done;
+            }
+        }
+        for (i = 0; i < shpc->nslots; ++i) {
+            if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) {
+                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
+                                  SHPC_STATE_PWRONLY, SHPC_LED_ON, 
SHPC_LED_NO);
+            } else {
+                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
+                                  SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO);
+            }
+        }
+        break;
+    case 0x49:
+        /* Enable all slots */
+        /* TODO: Spec says this shall fail if some are already enabled.
+         * This doesn't make sense - why not? a spec bug? */
+        for (i = 0; i < shpc->nslots; ++i) {
+            state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK);
+            if (state == SHPC_STATE_ENABLED) {
+                shpc_invalid_command(shpc);
+                goto done;
+            }
+        }
+        for (i = 0; i < shpc->nslots; ++i) {
+            if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) {
+                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
+                                  SHPC_STATE_ENABLED, SHPC_LED_ON, 
SHPC_LED_NO);
+            } else {
+                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
+                                  SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO);
+            }
+        }
+        break;
+    default:
+        shpc_invalid_command(shpc);
+        break;
+    }
+done:
+    pci_long_test_and_set_mask(shpc->config + SHPC_SERR_INT, 
SHPC_CMD_DETECTED);
+}
+
+static void shpc_write(PCIDevice *d, unsigned addr, uint64_t val, int l)
+{
+    SHPCDevice *shpc = d->shpc;
+    int i;
+    if (addr >= SHPC_SIZEOF(d)) {
+        return;
+    }
+    l = MIN(l, SHPC_SIZEOF(d) - addr);
+
+    /* TODO: code duplicated from pci.c */
+    for (i = 0; i < l; val >>= 8, ++i) {
+        unsigned a = addr + i;
+        uint8_t wmask = shpc->wmask[a];
+        uint8_t w1cmask = shpc->w1cmask[a];
+        assert(!(wmask & w1cmask));
+        shpc->config[a] = (shpc->config[a] & ~wmask) | (val & wmask);
+        shpc->config[a] &= ~(val & w1cmask); /* W1C: Write 1 to Clear */
+    }
+    if (ranges_overlap(addr, l, SHPC_CMD_CODE, 2)) {
+        shpc_command(shpc);
+    }
+    shpc_interrupt_update(d);
+}
+
+static uint64_t shpc_read(PCIDevice *d, unsigned addr, int l)
+{
+    uint64_t val = 0x0;
+    if (addr >= SHPC_SIZEOF(d)) {
+        return val;
+    }
+    l = MIN(l, SHPC_SIZEOF(d) - addr);
+    memcpy(&val, d->shpc->config + addr, l);
+    return val;
+}
+
+/* SHPC Bridge Capability */
+#define SHPC_CAP_LENGTH 0x08
+#define SHPC_CAP_DWORD_SELECT 0x2 /* 1 byte */
+#define SHPC_CAP_CxP 0x3 /* 1 byte: CSP, CIP */
+#define SHPC_CAP_DWORD_DATA 0x4 /* 4 bytes */
+#define SHPC_CAP_CSP_MASK 0x4
+#define SHPC_CAP_CIP_MASK 0x8
+
+static uint8_t shpc_cap_dword(PCIDevice *d)
+{
+    return pci_get_byte(d->config + d->shpc->cap + SHPC_CAP_DWORD_SELECT);
+}
+
+/* Update dword data capability register */
+static void shpc_cap_update_dword(PCIDevice *d)
+{
+    unsigned data;
+    data = shpc_read(d, shpc_cap_dword(d) * 4, 4);
+    pci_set_long(d->config  + d->shpc->cap + SHPC_CAP_DWORD_DATA, data);
+}
+
+/* Add SHPC capability to the config space for the device. */
+static int shpc_cap_add_config(PCIDevice *d)
+{
+    uint8_t *config;
+    int config_offset;
+    config_offset = pci_add_capability(d, PCI_CAP_ID_SHPC,
+                                       0, SHPC_CAP_LENGTH);
+    if (config_offset < 0) {
+        return config_offset;
+    }
+    config = d->config + config_offset;
+
+    pci_set_byte(config + SHPC_CAP_DWORD_SELECT, 0);
+    pci_set_byte(config + SHPC_CAP_CxP, 0);
+    pci_set_long(config + SHPC_CAP_DWORD_DATA, 0);
+    d->shpc->cap = config_offset;
+    /* Make dword select and data writeable. */
+    pci_set_byte(d->wmask + config_offset + SHPC_CAP_DWORD_SELECT, 0xff);
+    pci_set_long(d->wmask + config_offset + SHPC_CAP_DWORD_DATA, 0xffffffff);
+    return 0;
+}
+
+static uint64_t shpc_mmio_read(void *opaque, target_phys_addr_t addr,
+                               unsigned size)
+{
+    return shpc_read(opaque, addr, size);
+}
+
+static void shpc_mmio_write(void *opaque, target_phys_addr_t addr,
+                            uint64_t val, unsigned size)
+{
+    shpc_write(opaque, addr, val, size);
+}
+
+static const MemoryRegionOps shpc_mmio_ops = {
+    .read = shpc_mmio_read,
+    .write = shpc_mmio_write,
+    .endianness = DEVICE_LITTLE_ENDIAN,
+    .valid = {
+        /* SHPC ECN requires dword accesses, but the original 1.0 spec doesn't.
+         * It's easier to suppport all sizes than worry about it. */
+        .min_access_size = 1,
+        .max_access_size = 4,
+    },
+};
+
+static int shpc_device_hotplug(DeviceState *qdev, PCIDevice *affected_dev,
+                               PCIHotplugState hotplug_state)
+{
+    int pci_slot = PCI_SLOT(affected_dev->devfn);
+    uint8_t state;
+    uint8_t led;
+    PCIDevice *d = DO_UPCAST(PCIDevice, qdev, qdev);
+    SHPCDevice *shpc = d->shpc;
+    int slot = SHPC_PCI_TO_IDX(pci_slot);
+    if (pci_slot < SHPC_IDX_TO_PCI(0) || slot >= shpc->nslots) {
+        error_report("Unsupported PCI slot %d for standard hotplug "
+                     "controller. Valid slots are between %d and %d.",
+                     pci_slot, SHPC_IDX_TO_PCI(0),
+                     SHPC_IDX_TO_PCI(shpc->nslots) - 1);
+        return -1;
+    }
+    /* Don't send event when device is enabled during qemu machine creation:
+     * it is present on boot, no hotplug event is necessary. We do send an
+     * event when the device is disabled later. */
+    if (hotplug_state == PCI_COLDPLUG_ENABLED) {
+        shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN);
+        shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W,
+                        SHPC_SLOT_STATUS_PRSNT_MASK);
+        return 0;
+    }
+    if (hotplug_state == PCI_HOTPLUG_DISABLED) {
+        shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= SHPC_SLOT_EVENT_BUTTON;
+        state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK);
+        led = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK);
+        if (state == SHPC_STATE_DISABLED && led == SHPC_LED_OFF) {
+            shpc_free_devices_in_slot(shpc, slot);
+            shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN);
+            shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY,
+                            SHPC_SLOT_STATUS_PRSNT_MASK);
+            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
+                SHPC_SLOT_EVENT_MRL |
+                SHPC_SLOT_EVENT_PRESENCE;
+        }
+    } else {
+        /* This could be a cancellation of the previous removal.
+         * We check MRL state to figure out. */
+        if (shpc_get_status(shpc, slot, SHPC_SLOT_STATUS_MRL_OPEN)) {
+            shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN);
+            shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W,
+                            SHPC_SLOT_STATUS_PRSNT_MASK);
+            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
+                SHPC_SLOT_EVENT_BUTTON |
+                SHPC_SLOT_EVENT_MRL |
+                SHPC_SLOT_EVENT_PRESENCE;
+        } else {
+            /* Press attention button to cancel removal */
+            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
+                SHPC_SLOT_EVENT_BUTTON;
+        }
+    }
+    shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_66);
+    shpc_interrupt_update(d);
+    return 0;
+}
+
+/* Initialize the SHPC structure in bridge's BAR. */
+int shpc_init(PCIDevice *d, PCIBus *sec_bus, MemoryRegion *bar, unsigned 
offset)
+{
+    int i, ret;
+    int nslots = SHPC_MAX_SLOTS; /* TODO: qdev property? */
+    SHPCDevice *shpc = d->shpc = g_malloc0(sizeof(*d->shpc));
+    shpc->sec_bus = sec_bus;
+    ret = shpc_cap_add_config(d);
+    if (ret) {
+        g_free(d->shpc);
+        return ret;
+    }
+    if (nslots < SHPC_MIN_SLOTS) {
+        return 0;
+    }
+    if (nslots > SHPC_MAX_SLOTS ||
+        SHPC_IDX_TO_PCI(nslots) > PCI_SLOT_MAX) {
+        /* TODO: report an error mesage that makes sense. */
+        return -EINVAL;
+    }
+    shpc->nslots = nslots;
+    shpc->config = g_malloc0(SHPC_SIZEOF(d));
+    shpc->cmask = g_malloc0(SHPC_SIZEOF(d));
+    shpc->wmask = g_malloc0(SHPC_SIZEOF(d));
+    shpc->w1cmask = g_malloc0(SHPC_SIZEOF(d));
+
+    shpc_reset(d);
+
+    pci_set_long(shpc->config + SHPC_BASE_OFFSET, offset);
+
+    pci_set_byte(shpc->wmask + SHPC_CMD_CODE, 0xff);
+    pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX);
+    pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX);
+    pci_set_long(shpc->wmask + SHPC_SERR_INT,
+                 SHPC_INT_DIS |
+                 SHPC_SERR_DIS |
+                 SHPC_CMD_INT_DIS |
+                 SHPC_ARB_SERR_DIS);
+    pci_set_long(shpc->w1cmask + SHPC_SERR_INT,
+                 SHPC_CMD_DETECTED |
+                 SHPC_ARB_DETECTED);
+    for (i = 0; i < nslots; ++i) {
+        pci_set_byte(shpc->wmask +
+                     SHPC_SLOT_EVENT_SERR_INT_DIS(d, i),
+                     SHPC_SLOT_EVENT_PRESENCE |
+                     SHPC_SLOT_EVENT_ISOLATED_FAULT |
+                     SHPC_SLOT_EVENT_BUTTON |
+                     SHPC_SLOT_EVENT_MRL |
+                     SHPC_SLOT_EVENT_CONNECTED_FAULT |
+                     SHPC_SLOT_EVENT_MRL_SERR_DIS |
+                     SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS);
+        pci_set_byte(shpc->w1cmask +
+                     SHPC_SLOT_EVENT_LATCH(i),
+                     SHPC_SLOT_EVENT_PRESENCE |
+                     SHPC_SLOT_EVENT_ISOLATED_FAULT |
+                     SHPC_SLOT_EVENT_BUTTON |
+                     SHPC_SLOT_EVENT_MRL |
+                     SHPC_SLOT_EVENT_CONNECTED_FAULT);
+    }
+
+    /* TODO: init cmask */
+    memory_region_init_io(&shpc->mmio, &shpc_mmio_ops, d, "shpc-mmio",
+                          SHPC_SIZEOF(d));
+    shpc_cap_update_dword(d);
+    memory_region_add_subregion(bar, offset, &shpc->mmio);
+    pci_bus_hotplug(sec_bus, shpc_device_hotplug, &d->qdev);
+
+    d->cap_present |= QEMU_PCI_CAP_SHPC;
+    return 0;
+}
+
+int shpc_bar_size(PCIDevice *d)
+{
+    return roundup_pow_of_two(SHPC_SLOT_REG(SHPC_MAX_SLOTS));
+}
+
+void shpc_cleanup(PCIDevice *d, MemoryRegion *bar)
+{
+    SHPCDevice *shpc = d->shpc;
+    d->cap_present &= ~QEMU_PCI_CAP_SHPC;
+    memory_region_del_subregion(bar, &shpc->mmio);
+    /* TODO: cleanup config space changes? */
+    g_free(shpc->config);
+    g_free(shpc->cmask);
+    g_free(shpc->wmask);
+    g_free(shpc->w1cmask);
+    memory_region_destroy(&shpc->mmio);
+    g_free(shpc);
+}
+
+void shpc_cap_write_config(PCIDevice *d, uint32_t addr, uint32_t val, int l)
+{
+    if (!ranges_overlap(addr, l, d->shpc->cap, SHPC_CAP_LENGTH)) {
+        return;
+    }
+    fprintf(stderr, "%s: 0x%x 0x%x %d\n", __func__, addr, val, l);
+    if (ranges_overlap(addr, l, d->shpc->cap + SHPC_CAP_DWORD_DATA, 4)) {
+        unsigned dword_data;
+        dword_data = pci_get_long(d->shpc->config + d->shpc->cap
+                                  + SHPC_CAP_DWORD_DATA);
+        shpc_write(d, shpc_cap_dword(d) * 4, dword_data, 4);
+    }
+    /* Update cap dword data in case guest is going to read it. */
+    shpc_cap_update_dword(d);
+}
+
+static void shpc_save(QEMUFile *f, void *pv, size_t size)
+{
+    PCIDevice *d = container_of(pv, PCIDevice, shpc);
+    qemu_put_buffer(f, d->shpc->config, SHPC_SIZEOF(d));
+}
+
+static int shpc_load(QEMUFile *f, void *pv, size_t size)
+{
+    PCIDevice *d = container_of(pv, PCIDevice, shpc);
+    int ret = qemu_get_buffer(f, d->shpc->config, SHPC_SIZEOF(d));
+    if (ret != SHPC_SIZEOF(d)) {
+        return -EINVAL;
+    }
+    shpc_interrupt_update(d);
+    return 0;
+}
+
+VMStateInfo shpc_vmstate_info = {
+    .name = "shpc",
+    .get  = shpc_load,
+    .put  = shpc_save,
+};
diff --git a/hw/shpc.h b/hw/shpc.h
new file mode 100644
index 0000000..681eb85
--- /dev/null
+++ b/hw/shpc.h
@@ -0,0 +1,45 @@
+#ifndef SHPC_H
+#define SHPC_H
+
+#include "qemu-common.h"
+#include "memory.h"
+#include "vmstate.h"
+
+struct SHPCDevice {
+    /* Capability offset in device's config space */
+    int cap;
+
+    /* # of hot-pluggable slots */
+    int nslots;
+
+    /* SHPC WRS: working register set */
+    uint8_t *config;
+
+    /* Used to enable checks on load. Note that writable bits are
+     * never checked even if set in cmask. */
+    uint8_t *cmask;
+
+    /* Used to implement R/W bytes */
+    uint8_t *wmask;
+
+    /* Used to implement RW1C(Write 1 to Clear) bytes */
+    uint8_t *w1cmask;
+
+    /* MMIO for the SHPC BAR */
+    MemoryRegion mmio;
+
+    /* Bus controlled by this SHPC */
+    PCIBus *sec_bus;
+};
+
+void shpc_reset(PCIDevice *d);
+int shpc_bar_size(PCIDevice *dev);
+int shpc_init(PCIDevice *dev, PCIBus *sec_bus, MemoryRegion *bar, unsigned 
off);
+void shpc_cleanup(PCIDevice *dev, MemoryRegion *bar);
+void shpc_cap_write_config(PCIDevice *d, uint32_t addr, uint32_t val, int len);
+
+extern VMStateInfo shpc_vmstate_info;
+#define SHPC_VMSTATE(_field, _type) \
+    VMSTATE_BUFFER_UNSAFE_INFO(_field, _type, 0, shpc_vmstate_info, 0)
+
+#endif
diff --git a/qemu-common.h b/qemu-common.h
index c5e9cad..dee4db3 100644
--- a/qemu-common.h
+++ b/qemu-common.h
@@ -247,6 +247,7 @@ typedef struct SSIBus SSIBus;
 typedef struct EventNotifier EventNotifier;
 typedef struct VirtIODevice VirtIODevice;
 typedef struct QEMUSGList QEMUSGList;
+typedef struct SHPCDevice SHPCDevice;
 
 typedef uint64_t pcibus_t;
 
-- 
1.7.9.111.gf3fb0




reply via email to

[Prev in Thread] Current Thread [Next in Thread]