[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] [Bug 1732959] Re: [regression] Clock jump on source VM afte
From: |
Neil Skrypuch |
Subject: |
[Qemu-devel] [Bug 1732959] Re: [regression] Clock jump on source VM after migration |
Date: |
Wed, 21 Feb 2018 16:55:12 -0000 |
As a further test, I disabled ntpd on the host and ran ntpdate via cron
every 12 hours, so that the clock would be relatively accurate, but no
clock skew would be involved. This also reproduced the failure as
initially described.
This is interesting as it means that a much simpler and faster
reproduction case is probably feasible, something like:
1) start guest
2) jump host clock by a few seconds
3) migrate + cont src guest
4) check clock in src guest
Though, I haven't tried this yet.
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1732959
Title:
[regression] Clock jump on source VM after migration
Status in QEMU:
New
Bug description:
We (ab)use migration + block mirroring to perform transparent zero
downtime VM backups. Basically:
1) do a block mirror of the source VM's disk
2) migrate the source VM to a destination VM using the disk copy
3) cancel the block mirroring
4) resume the source VM
5) shut down the destination VM gracefully and move the disk to backup
Relatively recently, the source VM's clock started jumping after step
#4. More specifically, the clock jumps an amount of time proportional
to the time since it was last migrated. With a week between
migrations, clock jumps between ~2.5s and ~12s have been observed. For
a particular host, the amount of clock jump is fairly consistent, but
there is a large variation from one host to the next (this is likely
down to hardware variations and the amount of NTP adjusted clock drift
on the host).
This is caused by a kernel regression which I was able to bisect. The
result of the bisect was:
108b249c453dd7132599ab6dc7e435a7036c193f is the first bad commit
commit 108b249c453dd7132599ab6dc7e435a7036c193f
Author: Paolo Bonzini <address@hidden>
Date: Thu Sep 1 14:21:03 2016 +0200
KVM: x86: introduce get_kvmclock_ns
Introduce a function that reads the exact nanoseconds value that is
provided to the guest in kvmclock. This crystallizes the notion of
kvmclock as a thin veneer over a stable TSC, that the guest will
(hopefully) convert with NTP. In other words, kvmclock is *not* a
paravirtualized host-to-guest NTP.
Drop the get_kernel_ns() function, that was used both to get the base
value of the master clock and to get the current value of kvmclock.
The former use is replaced by ktime_get_boot_ns(), the latter is
the purpose of get_kernel_ns().
This also allows KVM to provide a Hyper-V time reference counter that
is synchronized with the time that is computed from the TSC page.
Reviewed-by: Roman Kagan <address@hidden>
Signed-off-by: Paolo Bonzini <address@hidden>
I am able to reproduce the issue with much newer kernels as well,
including 4.12.5 and 4.9.6.
Reliably reproducing the problem in isolation is difficult, as one
must run a VM for many hours before the clock jump from this bug is
noticeable over the clock jump inherent with a pause and resume of the
VM. The reproducer I am including is set to run the VM for 18 hours
before migration and looks for >= 150 ms of clock jump. On different
hardware, you may need to let the VM run for more than 18 hours to
reliably reproduce the issue.
To reproduce the issue, please see the attached reproducer. The host
needs to have perl, screen and socat installed for the backup script
to work. Both the host and guest need to be running NTP (and NTP must
autostart at boot in the guest). The host needs to be able to SSH into
the guest using SSH keys (to measure the clock jump), so you will need
to configure the network and SSH keys appropriately, then change the
hardcoded IP address in checktime.sh and test.sh. I have only tested
with CentOS 7 guests.
The qemu command that gets run is in .kvmscreen (the destination VM's
command line is programmatically constructed from this command as
well), you may need to tweak the bridge configuration. Also, although
the reproducer is relatively self contained, it has several built in
assumptions that will break if the image file is not in the
/var/lib/kvm directory or if the monitor file is not in the
/var/lib/kvm/monitor directory, or if the /backup directory does not
exist. Finally, if you change the process name or socket name in
.kvmscreen, you'll need to adjust the cleanup section in test.sh.
With all of the above in place, run test.sh and check back in a little
over 18 hours, part of the output should include something along these
lines:
Target not found (wanted 150, at 10)
- or -
Target found (wanted 150, found 340)
If the target is reported as found, that means that we have probably
reproduced the described issue.
The version of QEMU in use does not appear to matter. At one point I
tested every major version from 2.4 to 2.9 (inclusive) and reproduced
the issue in all of them.
This was initially observed on two different Gentoo hosts. I have also
started to see this issue happening with four different RHEL 7 hosts
as of the upgrade to RHEL 7.4. This is not too surprising as it
appears that the above commit has been backported into RHEL 7. All
hosts and guests are 64-bit.
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1732959/+subscriptions