[PATCH v2 11/22] migration/savevm: don't worry if bitmap migration postcopy failed

[Vladimir Sementsov-Ogievskiy]

First, if only bitmaps postcopy enabled (not ram postcopy)
postcopy_pause_incoming crashes on assertion assert(mis->to_src_file).

And anyway, bitmaps postcopy is not prepared to be somehow recovered.
The original idea instead is that if bitmaps postcopy failed, we just
loss some bitmaps, which is not critical. So, on failure we just need
to remove unfinished bitmaps and guest should continue execution on
destination.

Signed-off-by: Vladimir Sementsov-Ogievskiy <address@hidden>
---
 migration/savevm.c | 37 ++++++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)

diff --git a/migration/savevm.c b/migration/savevm.c
index 1d4220ece8..7e9dd58ccb 100644
--- a/migration/savevm.c
+++ b/migration/savevm.c
@@ -1812,6 +1812,9 @@ static void *postcopy_ram_listen_thread(void *opaque)
     MigrationIncomingState *mis = migration_incoming_get_current();
     QEMUFile *f = mis->from_src_file;
     int load_res;
+    MigrationState *migr = migrate_get_current();
+
+    object_ref(OBJECT(migr));
 
     migrate_set_state(&mis->state, MIGRATION_STATUS_ACTIVE,
                                    MIGRATION_STATUS_POSTCOPY_ACTIVE);
@@ -1838,11 +1841,24 @@ static void *postcopy_ram_listen_thread(void *opaque)
 
     trace_postcopy_ram_listen_thread_exit();
     if (load_res < 0) {
-        error_report("%s: loadvm failed: %d", __func__, load_res);
         qemu_file_set_error(f, load_res);
-        migrate_set_state(&mis->state, MIGRATION_STATUS_POSTCOPY_ACTIVE,
-                                       MIGRATION_STATUS_FAILED);
-    } else {
+        dirty_bitmap_mig_cancel_incoming();
+        if (postcopy_state_get() == POSTCOPY_INCOMING_RUNNING &&
+            !migrate_postcopy_ram() && migrate_dirty_bitmaps())
+        {
+            error_report("%s: loadvm failed during postcopy: %d. All state is "
+                         "migrated except for dirty bitmaps. Some dirty "
+                         "bitmaps may be lost, and present migrated dirty "
+                         "bitmaps are correctly migrated and valid.",
+                         __func__, load_res);
+            load_res = 0; /* prevent further exit() */
+        } else {
+            error_report("%s: loadvm failed: %d", __func__, load_res);
+            migrate_set_state(&mis->state, MIGRATION_STATUS_POSTCOPY_ACTIVE,
+                                           MIGRATION_STATUS_FAILED);
+        }
+    }
+    if (load_res >= 0) {
         /*
          * This looks good, but it's possible that the device loading in the
          * main thread hasn't finished yet, and so we might not be in 'RUN'
@@ -1878,6 +1894,8 @@ static void *postcopy_ram_listen_thread(void *opaque)
     mis->have_listen_thread = false;
     postcopy_state_set(POSTCOPY_INCOMING_END);
 
+    object_unref(OBJECT(migr));
+
     return NULL;
 }
 
@@ -2429,6 +2447,8 @@ static bool 
postcopy_pause_incoming(MigrationIncomingState *mis)
 {
     trace_postcopy_pause_incoming();
 
+    assert(migrate_postcopy_ram());
+
     /* Clear the triggered bit to allow one recovery */
     mis->postcopy_recover_triggered = false;
 
@@ -2513,15 +2533,22 @@ out:
     if (ret < 0) {
         qemu_file_set_error(f, ret);
 
+        /* Cancel bitmaps incoming regardless of recovery */
+        dirty_bitmap_mig_cancel_incoming();
+
         /*
          * If we are during an active postcopy, then we pause instead
          * of bail out to at least keep the VM's dirty data.  Note
          * that POSTCOPY_INCOMING_LISTENING stage is still not enough,
          * during which we're still receiving device states and we
          * still haven't yet started the VM on destination.
+         *
+         * Only RAM postcopy supports recovery. Still, if RAM postcopy is
+         * enabled, canceled bitmaps postcopy will not affect RAM postcopy
+         * recovering.
          */
         if (postcopy_state_get() == POSTCOPY_INCOMING_RUNNING &&
-            postcopy_pause_incoming(mis)) {
+            migrate_postcopy_ram() && postcopy_pause_incoming(mis)) {
             /* Reset f to point to the newly created channel */
             f = mis->from_src_file;
             goto retry;
-- 
2.21.0