[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[RFC PATCH v3 0/3] hw/flash_cfi01: Reduce memory consumption when flash

From: David Edmondson
Subject: [RFC PATCH v3 0/3] hw/flash_cfi01: Reduce memory consumption when flash image is smaller than region
Date: Mon, 22 Feb 2021 17:47:54 +0000

As described in
I'd like to reduce the amount of memory consumed by QEMU mapping UEFI
images on aarch64.

To recap:

> Currently ARM UEFI images are typically built as 2MB/768kB flash
> images for code and variables respectively. These images are both
> then padded out to 64MB before being loaded by QEMU.
> Because the images are 64MB each, QEMU allocates 128MB of memory to
> read them, and then proceeds to read all 128MB from disk (dirtying
> the memory). Of this 128MB less than 3MB is useful - the rest is
> zero padding.
> On a machine with 100 VMs this wastes over 12GB of memory.

There were objections to my previous patch because it changed the size
of the regions reported to the guest via the memory map (the reported
size depended on the size of the image).

This is a smaller patch which changes the memory region that covers
the entire region to be IO rather than RAM, and loads the flash image
into a smaller sub-region that is the more traditional mixed IO/ROMD

All read/write operations to areas outside of the underlying block
device are handled directly (reads return 0, writes fail or are

This reduces the memory consumption for the AAVMF code image from
64MiB to around 2MB and that for the AAVMF vars from 64MiB to 768KiB
(presuming that the UEFI images are adjusted accordingly).

For read-only devices (such as the AAVMF code) this seems completely

For writable devices there is a change in behaviour - previously it
was possible to write anywhere in the extent of the flash device, read
back the data written and have that data persist through a restart of
QEMU. This is no longer the case - writes outside of the extent of the
underlying backing block device will be discarded. That is, a read
after a write will *not* return the written data, either immediately
or after a QEMU restart - it will return zeros.

Looking at the AAVMF implementation, it seems to me that if the
initial VARS image is prepared as being 768KiB in size (which it is),
none of AAVMF itself will attempt to write outside of that extent, and
so I believe that this is an acceptable compromise.

It would be relatively straightforward to allow writes outside of the
backing device to persist for the lifetime of a particular QEMU by
allocating memory on demand (i.e. when there is a write to the
relevant region). This would allow a read to return the relevant data,
but only until a QEMU restart, at which point the data would be lost.

There was a suggestion in a previous thread that perhaps the pflash
driver could be re-worked to use the block IO interfaces to access the
underlying device "on demand" rather than reading in the entire image
at startup (at least, that's how I understood the comment).

I looked at implementing this and struggled to get it to work for all
of the required use cases. Specifically, there are several code paths
that expect to retrieve a pointer to the flat memory image of the
pflash device and manipulate it directly (examples include the Malta
board and encrypted memory support on x86), or write the entire image
to storage (after migration).

My implementation was based around mapping the flash region only for
IO, which meant that every read or write had to be handled directly by
the pflash driver (there was no ROMD style operation), which also made
booting an aarch64 VM noticeably slower - getting through the firmware
went from under 1 second to around 10 seconds.

- Unify the approach for both read-only and writable devices, saving
  another 63MiB per QEMU instance.

- Add Reviewed-by: for two changes (Philippe).
- Call blk_pread() directly rather than using
  blk_check_size_and_read_all(), given that we know how much we want
  to read.

David Edmondson (3):
  hw/pflash_cfi*: Replace DPRINTF with trace events
  hw/pflash_cfi01: Correct the type of PFlashCFI01.ro
  hw/pflash_cfi01: Allow devices to have a smaller backing device

 hw/block/pflash_cfi01.c | 188 +++++++++++++++++++++++++---------------
 hw/block/pflash_cfi02.c |  75 +++++++---------
 hw/block/trace-events   |  42 +++++++--
 3 files changed, 181 insertions(+), 124 deletions(-)


reply via email to

[Prev in Thread] Current Thread [Next in Thread]