[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: FC3, Nokia 6230i, DKU-2 USB
From: |
Christopher Kemp |
Subject: |
Re: FC3, Nokia 6230i, DKU-2 USB |
Date: |
Sat, 11 Jun 2005 16:31:29 +0100 |
On 2005.06.11 16:02 Del wrote:
Hi,
A couple of notes on getting gnokii 0.6.7 running on Fedora Core 3 with a
Nokia 6230i and a DKU2 USB cable. Kernel 2.6.11-1.27_FC3.
I have the phone working fine talking USB to the kernel without gnokii.
e.g. I was able to copy a bunch of files to and from the MMC card by
using
the KDE file manager, as hald noticed that it was a USB storage device,
when
I put the phone into data storage mode.
* The instructions in Docs/README-DK2 appear to be incorrect for the
driver
for the 2.6 kernel. It appears that instead of patching the kernel
sources,
the driver file there is supposed to be compiled using:
make ; make install
Good point, thanks.
Also it appears that the required usb-serial.h is not in the kernel
headers
set shipped with Fedora Core 3. I had to find a set of kernel sources
and
copy the usb-serial.h file from there, and put it into the
patches/kernel_2.6
before make would work.
Hmm
* The driver compiles OK but doesn't seem to work. When I plug the
phone in
to the USB port, however, another driver (cdc-acm) grabs it and sees the
phone,
as well as creates a /dev/ttyACM0 driver node (FC3 has devfs running).
Is it
possible to use the phone over this cdc-acm driver?
* e.g. I can modprobe the driver and it loads OK but I can't see the
dmesg
entries as suggested by the Doc/README-DKU2 file. I see messages from
the
cdc_acm module instead.
* Should I try to disable this cdc-acm driver? Will that hurt other USB
connectivity things?
Yes, you need to disable the cdc-acm driver - on some systems it grabs the
nokia device before my one and hence mine doesn't get used. The cdc-acm
driver provides AT functionality but not fbus, so only very little of
gnokii will work. I doubt any of your other usb devices us the cdc-acm
driver - if they do you'll not be able to use both at once (without fixing
the cdc-acm driver to not grab the nokia).
* Which .gnokiirc entries should I be using for this phone and connection
combination? I've tried model = AT and model = 6510 with no success so
far
(just running xgnokii fails to connect to the phone). Also which port =,
and connection = values should I be using?
Once you've got the module to be actually used you'll need to look at
dmesg to find which port it used. You want connection = dku2 and model =
6510.
* Are there some basic command-line connection tests I can run? There
doesn't
appear to be much in the documentation on this.
gnokii --identify
Regards, Chris
- FC3, Nokia 6230i, DKU-2 USB, Del, 2005/06/11
- Re: FC3, Nokia 6230i, DKU-2 USB,
Christopher Kemp <=
- Re: FC3, Nokia 6230i, DKU-2 USB, Del, 2005/06/12
- Re: FC3, Nokia 6230i, DKU-2 USB, Del, 2005/06/12
- Re: FC3, Nokia 6230i, DKU-2 USB, Pawel Kot, 2005/06/13
- Re: FC3, Nokia 6230i, DKU-2 USB, Del, 2005/06/13
- Re: FC3, Nokia 6230i, DKU-2 USB, Pawel Kot, 2005/06/13
- Re: FC3, Nokia 6230i, DKU-2 USB, Del, 2005/06/13
- Re: FC3, Nokia 6230i, DKU-2 USB, Pawel Kot, 2005/06/27
Re: FC3, Nokia 6230i, DKU-2 USB, Pawel Kot, 2005/06/11