LINUX gn_vm_initialise - gn_atem_initialise failed!

[ggb112]

Hello all

I am using gnokii-0.6.6 with a  7110 and a DAU9P cable.

I get the errors posted below when running gnokiid. How do I cure this 
problem?

There have been similar posts in the past but they have not covered this 
issue as
far as I can see.

I installed gnokii-0.6.6 as follows

 ./configure;make;make install;ldconfig

with /usr/local/lib in /etc/ld.so.conf.

Note that this is a transient error. I have tried this on two machines 
with the same
cable and phone. On the VIA it worked...

(i) gnokii-0.6.6's gnokiid works fine on an EPIA VIA with on board 
serial port!

(ii) The problem as pasted below appears on a desktop machine with the 
following cpu info

processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 8
model name      : Pentium III (Coppermine)
stepping        : 10
cpu MHz         : 999.692
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca 
cmov pat pse36 mmx fxsr sse
bogomips        : 1992.29


Please read the bug details below  which indicate a communiocation 
problem. Right at the very bottom is my .gnokiirc file.

Thanks so much

Gerard

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
Bug details....

Things to notice:

I have inserted some printfs into cfgreader.c to prove that the DAU9P in 
.gnokiirc was indeed picked up.
This results in the line "Found DAU9P" below.

I have also put a printf in fbus.c.
       printf("Gerard: Changed speed to 115200 in fbus.c: 1\n");

Should fbus.c be used at all???? Why is it changing the speed to 115200 
anyway when I asked for 19200
in the .gnokiirc file??

address@hidden gnokii-0.6.6]# gnokiid
GNOKIID Version 0.6.6
Found DAU9P
LOG: debug mask is 0x1
Initialising GSM
phone instance config:
model: 7110
port_device: /dev/ttyS1
connection_type: 1
init_length: 0
serial_baudrate: 19200
serial_write_usleep: 1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device /dev/ttyS1
Serial device: setting speed to 115200
Gerard: Changed speed to 115200 in fbus.c: 1
Serial device: setting RTS to low and DTR to high
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 03 01 32                               |      2
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 03 01 32                               |      2
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 03 01 32                               |      2
SM_Block: exiting the retry loop
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 03 01 32                               |      2
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 03 01 32                               |      2
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 03 01 32                               |      2
SM_Block: exiting the retry loop
gn_vm_initialise - gn_atem_initialise failed!





# gnokiid

[global]

port = /dev/ttyS1
model = 7110
initlength = default
connection = dau9p
use_locking = no
serial_baudrate = 19200
serial_write_usleep = 1
smsc_timeout = 10
[gnokiid]
bindir = /usr/local/sbin/
[connect_script]
TELEPHONE = 12345678
[disconnect_script]
[logging]
debug = on
rlpdebug = off
xdebug = off