discuss-gnuradio
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Discuss-gnuradio] RuntimeError: bad lexical cast: source type value


From: Josh Blum
Subject: Re: [Discuss-gnuradio] RuntimeError: bad lexical cast: source type value could not be interpreted as target
Date: Wed, 08 Dec 2010 19:36:01 -0800
User-agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.2.12) Gecko/20101027 Thunderbird/3.1.6

Alright, i was able to replicate the problem. If i tried to create a
multi usrp with one or more addresses that did not correspond to an
actual usrp it would throw "lexical cast error".

It wanted to throw "no control response error" but the exception threw
an exception. Anyway, I pushed a fix for this (thought i had already
fixed this prior).

So, in conclusion, I believe that you are addressing a the configuration
wrongly. The code needs polishing in that it wont check that the
addresses are found devices so it errors further down the line.

See
http://www.ettus.com/uhd_docs/manual/html/usrp_nxxx.html#soft-mimo-configuration

-Josh

On 12/08/2010 12:20 AM, Tobias Schmid wrote:
> I now rebuild uhd and gnuradio.
> But the error still occurs.
> 
> Running uhd_find_devices I get the following outputs:
> 
> linux; GNU C++ version 4.4.1 [gcc-4_4-branch revision 150839]; Boost_103900; 
> UHD_0001.20101204162446.a51fb2e
> 
> 
> Warning:
>  Could not locate USRP1 firmware.
>  Please install the images package.
>  
> --------------------------------------------------
> -- UHD Device 0
> --------------------------------------------------
> Device Address:
>  type: usrp2
>  addr: 192.168.10.2
>  name: 
>  serial: 00:50:c2:85:32:6b
> 
> 
> :/home/gnuradio/gnuradio/uhd/host/utils> uhd_find_devices 
> linux; GNU C++ version 4.4.1 [gcc-4_4-branch revision 150839]; Boost_103900; 
> UHD_0001.20101204162446.a51fb2e
> 
> 
> Warning:
>  Could not locate USRP1 firmware.
>  Please install the images package.
>  
> --------------------------------------------------
> -- UHD Device 0
> --------------------------------------------------
> Device Address:
>  type: usrp2
>  addr: 192.168.10.3
>  name: 
>  serial: 00:50:c2:85:32:66
> 
> Should I assign another IP address to the devices?
> It's also posslible to build up a SIS0 transmission with both USRPs.
> 
> But if I use the uhd_multi_usrp_source block, I get the same error as before:
> 
> 
> Generating: "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py"
> 
> Generating: "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py"
> 
> Executing: "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py"
> 
> linux; GNU C++ version 4.4.1 [gcc-4_4-branch revision 150839]; Boost_103900; 
> UHD_0001.20101204162446.a51fb2e
> 
> Current recv sock buff size: 50000000 bytes
> 
> Warning:
>  error in pthread_setschedparam
>  Failed to set thread priority 0.5 (realtime):
>  Performance may be negatively affected.
>  See the general application notes.
>  
> 
>>>> Done
> 
> Generating: "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py"
> 
> Generating: "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py"
> 
> Executing: "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py"
> 
> linux; GNU C++ version 4.4.1 [gcc-4_4-branch revision 150839]; Boost_103900; 
> UHD_0001.20101204162446.a51fb2e
> 
> Current recv sock buff size: 50000000 bytes
> Current recv sock buff size: 50000000 bytes
> Traceback (most recent call last):
>  File "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py", line 
> 96, in <module>
>  tb = uhd_test()
>  File "/home/tobias/Diplomarbeit/Implementierung/Blocktest/uhd_test.py", line 
> 36, in __init__
>  num_channels=2,
>  File "/usr/local/lib/python2.6/site-packages/gnuradio/uhd/uhd_swig.py", line 
> 1031, in multi_usrp_source
>  return _uhd_swig.multi_usrp_source(*args, **kwargs)
> RuntimeError: bad lexical cast: source type value could not be interpreted as 
> target
> 
>>>> Done
> 
> I hope I didn't ignore anything important.
> 
> Tobias
> 
> 
> 
> 
> -----Urspr√ľngliche Nachricht-----
> Von: "Tobias Schmid" <address@hidden>
> Gesendet: 07.12.2010 16:04:22
> An: address@hidden, address@hidden
> Betreff: Re: [Discuss-gnuradio] RuntimeError: bad lexical cast: source type 
> value could not be interpreted as target
> 
>> I tried to rebuild gnuradio, but now the uhd module is not found anymore.
>> So how do I rebuild my enviroment correctly?
>>
>> What I did is:
>>
>> In the uhd directory /host/build/ I did:
>>
>> make unistall
>> make clean
>> cd ..
>> cd ..
>> git pull
>> cd /host/build/
>> make
>> make test (all tests passed)
>> make install
>>
>> In the gburadio directory I did:
>>
>> make unistall
>> make clean
>> make distclean
>> git pull
>> git checkout next
>> git pull
>> git checkout master
>> ./configure
>> make
>> make check
>> make install
>>
>>
>> Is that right so far?
>>
>> Or is it necessary to delete some files by hand?
>>  Futhermore I do not have the same uhd blocks availible in grc.
>> I have just the older uhd blocks.
>>
>> I am able to probe both usrp individually.
>> The device arguments are 192.168.10.2 and 192.168.10.3.
>> Is that correct so far.
>>
>> I guess, that I have some older versions of symbolic links in my pythonpath.
>> Do you think that might be a possible reason?
>> If so, which directories can be deleted?
>>
>> Thanks,
>>
>> Tobias
>>
>> Am 02.12.2010 20:42, schrieb Josh Blum:
>>> I could not replicate the problem with the uhd_multi_usrp_source block.
>>> I only had a single usrp to test with, I can try out multiple next week
>>> when I get back to the office.
>>>
>>> Is it possible you have some weird device address arguments? My only two
>>> guesses are eeprom map parsing or some weird device address. When you
>>> ran the probe app, were you able to probe both usrps individually? That
>>> would let me know that the eeprom parsing works fine on both boards.
>>>
>>> Can you rebuilt gnuradio after rebuilding UHD just to be sure were not
>>> looking at some ABI change.
>>>
>>> -Josh
>>>
>>> On 12/01/2010 03:00 AM, Tobias Schmid wrote:
>>>    
>>>> Hello,
>>>>
>>>> sorry I had been out of office for some days.
>>>>
>>>> When I run uhd_usrp_probe the error doesn't occur.
>>>> And using uhd.single_usrp_source doesn't occur either.
>>>>
>>>> The complete output of the terminal is:
>>>>
>>>> linux; GNU C++ version 4.4.1 [gcc-4_4-branch revision 150839];
>>>> Boost_103900; UHD_0001.20101124180824.2568efd
>>>>
>>>> Current recv sock buff size: 50000000 bytes
>>>> Current recv sock buff size: 50000000 bytes
>>>> Traceback (most recent call last):
>>>>    File "/home/gnuradio/Desktop/top_block.py", line 95, in<module>
>>>>      tb = top_block()
>>>>    File "/home/gnuradio/Desktop/top_block.py", line 35, in __init__
>>>>      num_channels=2,
>>>>    File
>>>> "/usr/local/lib/python2.6/site-packages/gnuradio/uhd/uhd_swig.py", line
>>>> 1023, in multi_usrp_source
>>>>      return _uhd_swig.multi_usrp_source(*args, **kwargs)
>>>> RuntimeError: bad lexical cast: source type value could not be
>>>> interpreted as target
>>>>
>>>> The error also occurs when using udh.multi_usrp_sink.
>>>> Maybe that could be another hint.
>>>>
>>>> By the way, what do I have to do to run a discontinous data transmission
>>>> using uhd.single_usrp_source.
>>>> I implemented some ARQ-protocols using USRP driver. Now I wanted to
>>>> upgreade these applications, but it doesn't work well.
>>>>
>>>> Thanks,
>>>>
>>>> Tobias
>>>>
>>>> Am 26.11.2010 17:53, schrieb Josh Blum:
>>>>      
>>>>> boost lexical cast doesnt have a very telling error does it...
>>>>>
>>>>> Can you send me the complete verbose?
>>>>>
>>>>> Does the error happen when you run uhd_usrp_probe?
>>>>>
>>>>> Howabout uhd.single_usrp_source?
>>>>>
>>>>> Does GDB give any hint as to where the exception is thrown?
>>>>>
>>>>> Thanks,
>>>>> -Josh
>>>>>
>>>>> On 11/26/2010 04:05 AM, Tobias Schmid wrote:
>>>>>
>>>>>        
>>>>>> Hello,
>>>>>>
>>>>>> I'm trying to use 2 USRP2 using the UHD Driver.
>>>>>> My version is the git version of yesterday.
>>>>>>
>>>>>> But when I'm trying to build a flowgraph using grc,
>>>>>> gnuradio isn't able to run the generated code.
>>>>>>
>>>>>> The following error occurs:
>>>>>>
>>>>>> RuntimeError: bad lexical cast: source type value could not be
>>>>>> interpreted as target
>>>>>>
>>>>>> And this is the generated code:
>>>>>>
>>>>>> self.uhd_multi_usrp_source_0 = uhd.multi_usrp_source(
>>>>>> device_addr="addr=192.168.10.2 192.168.10.3",
>>>>>> io_type=uhd.io_type_t.COMPLEX_FLOAT32,
>>>>>> num_channels=2,
>>>>>> )
>>>>>> _clk_cfg = uhd.clock_config_t()
>>>>>> _clk_cfg.ref_source = uhd.clock_config_t.REF_SMA
>>>>>> _clk_cfg.pps_source = uhd.clock_config_t.PPS_SMA
>>>>>> _clk_cfg.pps_polarity = uhd.clock_config_t.PPS_POS
>>>>>> self.uhd_multi_usrp_source_0.set_clock_config(_clk_cfg,
>>>>>> uhd.ALL_MBOARDS);
>>>>>> self.uhd_multi_usrp_source_0.set_time_unknown_pps(uhd.time_spec_t())
>>>>>> self.uhd_multi_usrp_source_0.set_samp_rate(1000000)
>>>>>> self.uhd_multi_usrp_source_0.set_center_freq(2450000000, 0)
>>>>>> self.uhd_multi_usrp_source_0.set_gain(20, 0)
>>>>>> self.uhd_multi_usrp_source_0.set_center_freq(2450000000, 1)
>>>>>> self.uhd_multi_usrp_source_0.set_gain(20, 1)
>>>>>>
>>>>>> Can someone help me solving this problem?
>>>>>>
>>>>>> Best regards,
>>>>>>
>>>>>> Tobias
>>>>>>
>>>>>>
>>>>>>
>>>>>> Neu: WEB.DE De-Mail - Einfach wie E-Mail, sicher wie ein Brief!
>>>>>> Jetzt De-Mail-Adresse reservieren: https://produkte.web.de/go/demail02
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>>> Discuss-gnuradio mailing list
>>>>>> address@hidden
>>>>>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>>>>
>>>>>>          
>>>>> _______________________________________________
>>>>> Discuss-gnuradio mailing list
>>>>> address@hidden
>>>>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>>>
>>>>>
>>>>>        
>>>>      
>>
>>
>> _______________________________________________
>> Discuss-gnuradio mailing list
>> address@hidden
>> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
> ___________________________________________________________
> WEB.DE DSL Doppel-Flat ab 19,99 &euro;/mtl.! Jetzt auch mit 
> gratis Notebook-Flat! http://produkte.web.de/go/DSL_Doppel_Flatrate/2



reply via email to

[Prev in Thread] Current Thread [Next in Thread]