Re: [avr-chat] avrdude fails to write STK500 & AT90S8515

[Jose I. Monreal]

Thanks, that was the problem lol.

Could anyone please give me a hand? I want to turn the leds on, but one 
by one, how can i make that possible?

Thanks


Marge Coahran wrote:
> My new STK500 came with an ATMEGA8515L chip instead. Thus, I need to 
> use the following command. (Note the different chip specifier: 
> "m8515", not "8515".) Could that be your difficulty?
>
> avrdude -p m8515 -c stk500v2 -P /dev/ttyS0 -U flash:w:$(FILE).hex
>
> Marge
>
> On Thu, 13 Sep 2007, jmonreal wrote:
> > Hi, I'm new in the field. I have just acquire an STK500 AVR Starter 
> > Kit. It
> > comes with AT90S8515 micro-controller. I work only under GNU/Linux 
> > and I've
> > followed the steps to install all necesary software to work with this
> > "board". The thing is I keep getting the same error with avrdude
> >
> > $ avrdude -p 8515 -c stk500v2 -P /dev/ttyS0 -e -U flash:w:simple.hex:i
> >
> > avrdude: AVR device initialized and ready to accept instructions
> >
> > Reading | ################################################## | 100% 
> > 0.01s
> >
> > avrdude: Device signature = 0x1e9306
> > avrdude: erasing chip
> > avrdude: reading input file "simple.hex"
> > avrdude: writing flash (96 bytes):
> >
> > Writing | | 0% 0.00s
> > ***failed;
> > Writing | # | 1% 0.08s
> > ***failed;
> >
> > and it goes like that until 100%
> >
> > then,
> >
> > avrdude: 96 bytes of flash written
> > avrdude: verifying flash memory against simple.hex:
> > avrdude: load data flash data from input file simple.hex:
> > avrdude: input file simple.hex contains 96 bytes
> > avrdude: reading on-chip flash data:
> >
> > Reading | ################################################## | 100% 
> > 0.39s
> >
> > avrdude: verifying ...
> > avrdude: verification error, first mismatch at byte 0x0000
> > 0x0c != 0xff
> > avrdude: verification error; content mismatch
> >
> > avrdude done. Thank you.
> >
> >
> > I've been Googleing but nothing, hope you could help, Thanks.
> >
> > PS: I've tried windows but avr studio told me something about ISP 
> > frequency
> > mistaken :s
> >
> > this is what i get with avrdude -v option
> >
> > Using Port : /dev/ttyS0
> > Using Programmer : stk500v2
> > AVR Part : AT90S8515
> > Chip Erase delay : 20000 us
> > PAGEL : P00
> > BS2 : P00
> > RESET disposition : dedicated
> > RETRY pulse : SCK
> > serial program mode : yes
> > parallel program mode : yes
> > Timeout : 200
> > StabDelay : 100
> > CmdexeDelay : 25
> > SyncLoops : 32
> > ByteDelay : 0
> > PollIndex : 3
> > PollValue : 0x53
> > Memory Detail :
> >
> > Block Poll Page
> > Polled
> > Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW
> > MaxW ReadBack
> > ----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
> > ----- ---------
> > eeprom 4 12 128 0 no 512 0 0 4000
> > 9000 0x80 0x7f
> > flash 4 12 128 0 no 8192 0 0 4000
> > 9000 0x7f 0x7f
> > signature 0 0 0 0 no 3 0 0 0
> > 0 0x00 0x00
> > fuse 0 0 0 0 no 1 0 0 0
> > 0 0x00 0x00
> > lock 0 0 0 0 no 1 0 0 9000
> > 9000 0x00 0x00
> >
> > Programmer Type : STK500V2
> > Description : Atmel STK500 Version 2.x firmware
> > Programmer Model: STK500
> > Hardware Version: 2
> > Firmware Version: 2.10
> > Topcard : Unknown
> > Vtarget : 5.1 V
> > Varef : 5.0 V
> > Oscillator : 3.686 MHz
> > SCK period : 10.9 us
> >
> > avrdude: AVR device initialized and ready to accept instructions
> >
> > Reading | ################################################## | 100% 
> > 0.01s
> >
> > avrdude: Device signature = 0x1e9306
> > avrdude: safemode: Fuse reading not support by programmer.
> > Safemode disabled.
> >
> > avrdude done. Thank you.
> >
> >
> > Tanks!
> >
> >
> >
> >
> > --
> > View this message in context: 
> > http://www.nabble.com/avrdude-fails-to-write-STK500---AT90S8515-tf4433510.html#a12648491 
> >
> > Sent from the AVR - General mailing list archive at Nabble.com.
> >
> >
> >
> > _______________________________________________
> > AVR-chat mailing list
> > address@hidden
> > http://lists.nongnu.org/mailman/listinfo/avr-chat