[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] Sending pre-saved OFDM file to USRP
From: |
Hoo-chang Shin |
Subject: |
Re: [Discuss-gnuradio] Sending pre-saved OFDM file to USRP |
Date: |
Thu, 17 Apr 2008 08:36:30 -0700 (PDT) |
Thank you for your reply, Tom.
With the 'benchmark_ofdm_tx.py' and 'benchmark_ofdm_rx.py', I receive the right
packets using the command:
$ ./benchmark_ofdm_tx.py -T A -f 2.45G -i 512
$ ./benchmark_ofdm_rx.py -R A -f 2.45G -d 256
But when I send the pre-saved file (which is saved from the
'benchmark_ofdm_tx.py'), the 'benchmark_ofdm_rx.py' does not detect any packet
at the receiver side.
Viewing the received signal with usrp_fft.py, I see the same spectrum, as from
the 'benchmark_ofdm_tx.py' sent spectrum, though.
I send it with the same frequency, with the same interpolation rate, and with
the same gain value...
----- Original Message ----
From: Tom Rondeau <address@hidden>
To: Hoo-chang Shin <address@hidden>
Cc: address@hidden
Sent: Thursday, April 17, 2008 5:03:14 PM
Subject: Re: [Discuss-gnuradio] Sending pre-saved OFDM file to USRP
Hoo-chang Shin wrote:
> Well, I did it like that, it did not work with connecting the file_source
> direct to USRP.
> I thought then it might work when I do the 'vector thing' in the middle.
> In either case, the receiver USRP does not detect anything.
>
Have you tried to run usrp_fft.py at the receiver to make sure you see
some energy?
Also, have you just tried using benchmark_ofdm_tx.py on one side and
benchmark_ofdm_rx.py on another?
There are a lot of parameters to tweak. The amplitude is one important
one (high enough to be seen at the receiver, low enough to avoid
clipping), and the decim/interp values depend on the speed of your
processor.
FWIW, just saying the receiver isn't getting anything isn't too useful
when asking for help with all of the possible issues.
Tom
> ----- Original Message ----
> From: Tom Rondeau <address@hidden>
> To: Hoo-chang Shin <address@hidden>
> Cc: address@hidden
> Sent: Thursday, April 17, 2008 1:48:27 PM
> Subject: Re: [Discuss-gnuradio] Sending pre-saved OFDM file to USRP
>
> Hoo-chang Shin wrote:
>
>> Hi,
>>
>> I'm trying to send a pre-saved OFDM file to a transmitter USRP, and to
>> receive the signal from a receiver USRP.
>> >From the 'benchmark_ofdm_tx.py' I've saved the OFDM signal to a file using
>> >'gr.file_sink', instead of sending it to 'usrp.sink_c'.
>> And then I want to read the data from the saved file and send it though the
>> transmitter USRP, and receive it from the other USRP, but does not work.
>>
>> Could anyone give tip, why it does not work? Or give help how to make it
>> work?
>>
>>
>> This is my code:
>>
>> #!/usr/bin/env python
>>
>> from gnuradio import gr
>> from gnuradio import usrp
>>
>> from numpy import *
>>
>> class send_from_file_graph (gr.flow_graph):
>>
>> def __init__(self):
>> gr.flow_graph.__init__(self)
>>
>> filename = 'tx_usrp_data.dat'
>> # which I had saved from 'benchmark_ofdm_tx.py' using
>> 'gr.file_sink(gr.sizeof_gr_complex, filename)'
>> src = gr.file_source ( gr.sizeof_gr_complex, filename, False)
>>
>> self.v_snk = gr.vector_sink_c()
>>
>> # setup usrp
>> self.u = usrp.sink_c(fusb_block_size=0, fusb_nblocks=0)
>> self.u.set_interp_rate(512)
>> self._tx_subdev_spec = usrp.pick_tx_subdevice(self.u)
>> self.subdev = usrp.selected_subdev(self.u, self._tx_subdev_spec)
>>
>> self.u.tune(self.subdev._which, self.subdev, 2.45e9)
>> self.subdev.set_gain(200)
>> self.subdev.set_auto_tr(True)
>> # ##
>>
>> self.connect(src, self.v_snk)
>> self.run()
>> v_src = gr.vector_source_c(self.v_snk.data())
>> self.connect(v_src, self.u)
>> self.run()
>>
>
> Why don't you just do:
>
> self.connect(src, self.u)
>
> Instead of all the vector stuff in the middle?
>
> Tom
>
>
____________________________________________________________________________________
Be a better friend, newshound, and
know-it-all with Yahoo! Mobile. Try it now.
http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ