[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: [Discuss-gnuradio] Spectrum at 1 GHz
From: |
Ian Holland |
Subject: |
RE: [Discuss-gnuradio] Spectrum at 1 GHz |
Date: |
Tue, 13 Apr 2010 11:20:12 +0930 |
Hi Umair
There is a setting in the USRP2 source block that lets you set the
carrier frequency. This should be 1e9 (i.e. 1G).
What is the signal you are trying to receive?
Ian
-----Original Message-----
From: Umair Naeem [mailto:address@hidden
Sent: Monday, 12 April 2010 8:22 PM
To: Ian Holland
Subject: RE: [Discuss-gnuradio] Spectrum at 1 GHz
So If I need to see in the baseband region then what should be the
parameters of USRP2 source for my case (i.e. Decimation and Frequency).
Should I give 1 GHz in the frequency parameter or in the baseband
region?
Thanks for help...
Regards,
Umair Naeem
MSc Communication Engineering
Chalmers University ot Technology, Sweden.
________________________________________
From: Ian Holland address@hidden
Sent: Monday, April 12, 2010 9:55 AM
To: Umair Naeem; address@hidden
Subject: RE: [Discuss-gnuradio] Spectrum at 1 GHz
Hi Umair
I believe the decimation factor you have chosen is beyond the maximum
allowed (I think, from memory this is 512, which is well less than 1M =
1 times 10^6).
It seems you are trying to sample the passband signal to show a spectrum
at 1 GHz, however a digital-down conversion is performed at the
receiver, so you should see a signal at baseband. You should not need to
use such a high sampling rate - ideally, Nyquist rate (based on the
signal bandwidth when downconveted to baseband) will suffice.
Regards
Ian.
-----Original Message-----
From: address@hidden
[mailto:address@hidden On
Behalf Of Umair Naeem
Sent: Monday, 12 April 2010 4:59 PM
To: address@hidden
Subject: [Discuss-gnuradio] Spectrum at 1 GHz
I have a query regarding flow graph in GRC.
I am trying to get spectrum from DBS_RX daughter board using GRC. I have
used three blocks as
USRP2 Source --> FFT Filter --> FFT Sink
They have following parameters,
USRP2 Source:
Decimation 1M
Frequency 1G
Gain (dB) 0
FFT Filter:
Decimation 1
Taps firdes.complex_band_pass(1.0, 3000, -0.05e3, 0.05e3, 5,
firdes.WIN_HAMMING, 0)
FFT Sink:
Sample Rate 2K
Baseband Frequency 1K
FFT Size 512
Refresh Rate 30
I need to display shows frequency spectrum centered at 1 GHz. Since I am
using decimation of 1M, the frequency is lowered down to 1K. I filter it
using FFT bandpass filter with 100 Hz bandwidth. The fft sink shows
spectrum at around 1 KHz. The problem is if I do not use decimation, the
GRC seems to be very slow (may be processing 1 GHz at GHz sample rate
is too much). I need to make a FFT plot showing spectrum at 1 GHz. How
Can I accomplish this?
Regards,
Umair Naeem
MSc Communication Engineering
Chalmers University ot Technology, Sweden.
_______________________________________________
Discuss-gnuradio mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio