HI fellows,
I was wondering if anybody has been trying to reach 8 Complex Msps over the USB 2.0 on the Tx path.
While this has always been OK with old libusrp (and USRP 1) it appears to be no longer possible by means of UHD
neither when trying to do that on USRP1 (a few underruns) nor on B100 (lots of overruns).
Everything appears instead fine on the Rx path
Is there any workaround to this?
..or did I miss something?
thanks everybody
PS
USB 3.0 seems to be capable enough for the 8 Msps.
Is USB3.0 a requirement for 8 Msps on the B100?
Look for other devices on that USB bus using lsusb. Avoid sharing the bus with other peripherals (bluetooth, wlan, etc). You can also modify the transport parameters using --args=recv_frame_size=xxxxx,send_frame_size=xxxxx. This will give you the same control over receive & send frame size that the old USRP1 drivers had. The default receive/send frame sizes are 16K, which seems to work OK on most machines.
For comparison, the USB host controller I'm using is the Intel 6 Series/C200, and on B100 I can use a TX send rate of 10.67Msps without underflow, although occasionally underflows occur at the very beginning of the transmission (likely due to interrupt coalescing on the USB controller).
I also have a USB 3.0 controller (an NEC Corporation uPD720200) on this laptop, which fares more poorly, but still easily achieves 8Msps. I don't have a good explanation as to why some USB controllers do better than others. USB 3.0 is certainly not required on B100/USRP1, as neither device uses USB 3.0.
--n
____________________________________________________________B100
./benchmark_rate --tx_rate 8e6
linux; GNU C++ version 4.6.1 20110908 (Red Hat 4.6.1-9); Boost_104600; UHD_003.004.000-325-g7e296167
Creating the usrp device with: ...
-- USRP-B100 clock control: 10
-- r_counter: 2
-- a_counter: 0
-- b_counter: 20
-- prescaler: 8
-- vco_divider: 5
-- chan_divider: 5
-- vco_rate: 1600.000000MHz
-- chan_rate: 320.000000MHz
-- out_rate: 64.000000MHz
--
Using Device: Single USRP:
Device: B-Series Device
Mboard 0: B100 (B-Hundo)
RX Channel: 0
RX DSP: 0
RX Dboard: A
RX Subdev: WBX RX v3 + Simple GDB
TX Channel: 0
TX DSP: 0
TX Dboard: A
TX Subdev: WBX TX v3 + Simple GDB
Testing transmit rate 8.000000 Msps
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
Benchmark rate summary:
Num received samples: 0
Num dropped samples: 0
Num overflows detected: 0
Num transmitted samples: 79931260
Num sequence errors: 0
Num underflows detected: 406
Done!
./benchmark_rate --tx_rate 8e6 --tx_otw sc16
linux; GNU C++ version 4.6.1 20110908 (Red Hat 4.6.1-9); Boost_104600; UHD_003.004.000-325-g7e296167
Creating the usrp device with: ...
-- USRP-B100 clock control: 10
-- r_counter: 2
-- a_counter: 0
-- b_counter: 20
-- prescaler: 8
-- vco_divider: 5
-- chan_divider: 5
-- vco_rate: 1600.000000MHz
-- chan_rate: 320.000000MHz
-- out_rate: 64.000000MHz
--
Using Device: Single USRP:
Device: B-Series Device
Mboard 0: B100 (B-Hundo)
RX Channel: 0
RX DSP: 0
RX Dboard: A
RX Subdev: WBX RX v3 + Simple GDB
TX Channel: 0
TX DSP: 0
TX Dboard: A
TX Subdev: WBX TX v3 + Simple GDB
Testing transmit rate 8.000000 Msps
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
Benchmark rate summary:
Num received samples: 0
Num dropped samples: 0
Num overflows detected: 0
Num transmitted samples: 79890620
Num sequence errors: 0
Num underflows detected: 696
Done!
____________________________________________________________USRP 1
./benchmark_rate --tx_rate 8e6 --tx_otw sc16
linux; GNU C++ version 4.6.1 20110908 (Red Hat 4.6.1-9); Boost_104600; UHD_003.004.000-325-g7e296167
*** Warning! ***
Benchmark results will be inaccurate on USRP1 due to insufficient features.
Creating the usrp device with: ...
-- Opening a USRP1 device...
-- Using FPGA clock rate of 64.000000MHz...
Using Device: Single USRP:
Device: USRP1 Device
Mboard 0: USRP1 (Classic)
RX Channel: 0
RX DSP: 0
RX Dboard: B
RX Subdev: WBX RX v2 + Simple GDB
TX Channel: 0
TX DSP: 0
TX Dboard: B
TX Subdev: WBX TX v2 + Simple GDB
Testing transmit rate 8.000000 Msps
UUUUU
Benchmark rate summary:
Num received samples: 0
Num dropped samples: 0
Num overflows detected: 0
Num transmitted samples: 80022656
Num sequence errors: 0
Num underflows detected: 5
Done!
____________________________________________________________everything fine with 8bit samples
./benchmark_rate --tx_rate 8e6 --tx_otw sc8
linux; GNU C++ version 4.6.1 20110908 (Red Hat 4.6.1-9); Boost_104600; UHD_003.004.000-325-g7e296167
-- Loading firmware image: /usr/share/uhd/images/usrp_b100_fw.ihx... done
Creating the usrp device with: ...
-- USRP-B100 clock control: 10
-- r_counter: 2
-- a_counter: 0
-- b_counter: 20
-- prescaler: 8
-- vco_divider: 5
-- chan_divider: 5
-- vco_rate: 1600.000000MHz
-- chan_rate: 320.000000MHz
-- out_rate: 64.000000MHz
--
-- Loading FPGA image: /usr/share/uhd/images/usrp_b100_fpga.bin... done
Using Device: Single USRP:
Device: B-Series Device
Mboard 0: B100 (B-Hundo)
RX Channel: 0
RX DSP: 0
RX Dboard: A
RX Subdev: WBX RX v3 + Simple GDB
TX Channel: 0
TX DSP: 0
TX Dboard: A
TX Subdev: WBX TX v3 + Simple GDB
Testing transmit rate 8.000000 Msps
Benchmark rate summary:
Num received samples: 0
Num dropped samples: 0
Num overflows detected: 0
Num transmitted samples: 80053688
Num sequence errors: 0
Num underflows detected: 0
Done!
_______________________________________________
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio