[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] LED test on Lisa M2

From: Christophe De Wagter
Subject: Re: [Paparazzi-devel] LED test on Lisa M2
Date: Thu, 27 Sep 2012 21:48:36 +0200

@Felix: I think it would be nice if the build script would show the paparazzi version, what do you think?

On Sep 27, 2012 9:42 PM, "Gerard Toonstra" <address@hidden> wrote:

I've acquired 2 Lisa M2 boards from TRI and don't think I'm getting the correct results for the LED test.
The LED's remain on for the entire time and there's no single one blinking or any other following a kind of

When the AP is loaded, the red led is blinking @ 1Hz and the AHRS led blinks a while, then remains lit. This tells
me the timer is working. I've also been able to get serial output/input, as the GCS is showing a couple of messages
up to the GPS block (GPS is not yet configured).

With the tunnel firmware (in an attempt to configure my SkyTraq GPS), I'm getting no output whatsoever.
When the UART test is uploaded, all LEDs also turn on and remain fixed, but there's no output from the serial connector.

I've removed all other peripherals at this time and only use the USB to power the device.

Here's the output of the build and upload cycle:

CC /work/paparazzi/var/Maja/test_led/./mcu.o
CC /work/paparazzi/var/Maja/test_led/arch/stm32/mcu_arch.o
CC /work/paparazzi/var/Maja/test_led/arch/stm32/stm32_exceptions.o
CC /work/paparazzi/var/Maja/test_led/arch/stm32/stm32_vector_table.o
arch/stm32/stm32_vector_table.c:206:5: warning: taking address of _expression_ of type 'void' [enabled by default]
CC /work/paparazzi/var/Maja/test_led/mcu_periph/sys_time.o
CC /work/paparazzi/var/Maja/test_led/arch/stm32/mcu_periph/sys_time_arch.o
CC /work/paparazzi/var/Maja/test_led/arch/stm32/led_hw.o
CC /work/paparazzi/var/Maja/test_led/lisa/test_led.o
LD /work/paparazzi/var/Maja/test_led/test_led.elf
OBJCB /work/paparazzi/var/Maja/test_led/test_led.bin
OBJCH /work/paparazzi/var/Maja/test_led/test_led.hex

Current size:
/work/paparazzi/var/Maja/test_led/test_led.elf  :
section             size         addr
.isr_vector        0x130    0x8002000
.text              0x61c    0x8002130
.data                0x8   0x20000000
.bss                0xac   0x20000008
._usrstack         0x800   0x200000b4
.comment            0x3c          0x0
.ARM.attributes     0x31          0x0
.debug_aranges     0x588          0x0
.debug_info       0x3685          0x0
.debug_abbrev      0xfdd          0x0
.debug_line       0x1ee4          0x0
.debug_frame       0xa38          0x0
.debug_str        0x16d2          0x0
.debug_loc        0x106b          0x0
.debug_ranges      0x4f0          0x0
Total             0xb1a0

make[1]: Leaving directory `/work/paparazzi/sw/airborne'
make: Leaving directory `/work/paparazzi'

DONE (exec make -C /work/paparazzi -f AIRCRAFT=Maja test_led.compile  2>&1)

Run 'make -C /work/paparazzi -f AIRCRAFT=Maja test_led.upload '
make: Entering directory `/work/paparazzi'
cd sw/airborne; make PAPARAZZI_SRC=/work/paparazzi PAPARAZZI_HOME=/work/paparazzi TARGET=test_led all
make[1]: Entering directory `/work/paparazzi/sw/airborne'
Using CC   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc
Using LD   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-gcc
Using CP   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-objcopy
Using DMP  = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-objdump
Using NM   = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-nm
Using SIZE = /opt/paparazzi/arm-multilib/bin/arm-none-eabi-size
GCC version:
arm-none-eabi-gcc (Linaro GCC 4.6-2011.09-1) 4.6.2 20110908 (prerelease)
*** Using multilib ***

make[1]: Leaving directory `/work/paparazzi/sw/airborne'
cd sw/airborne; make PAPARAZZI_SRC=/work/paparazzi PAPARAZZI_HOME=/work/paparazzi TARGET=test_led upload
make[1]: Entering directory `/work/paparazzi/sw/airborne'
Using stm32 mem dfu loader
/usr/bin/python /work/paparazzi/sw/tools/dfu/ /work/paparazzi/var/Maja/test_led/test_led.bin

USB Device Firmware Upgrade - Host Utility -- version 1.2
Copyright (C) 2011  Black Sphere Technologies
Copyright (C) 2012  Transition Robotics Inc.
License GPLv3+: GNU GPL version 3 or later <>

Device 032: ID 1d50:600f Transition Robotics Inc. - Lisa/M (Upgrade) V1.0 - LM2-152 35FFDA053256383326432143
Programming memory at 0x08002000
All operations complete!


Any ideas or pointers?   Is it possible this is related to a configuration issue in the XML file?
Trying this on the other board, I'm getting exactly the same results.



Paparazzi-devel mailing list

reply via email to

[Prev in Thread] Current Thread [Next in Thread]